Filters
Sort by Position Name: A to Z Name: Z to A Price: Low to High Price: High to Low Created on Sku: A to Z Sku: Z to A
Display 12 20 24 100 per page
Add to compare list Add to wishlist
51-3661212
Stable U-shaped closed construction made of 3 mm sheet steel profile Support rollers made of galvanized steel All roller conveyors of the MRB standard series also available with plastic rollers Supported rollers ball-bearing The maximum measuring length is the length of the track minus the stop length 260 mm With length measuring device Roller and measuring track with mm-scale, manual measuring system with C-guide profile and sliding flap stop Quality Made in Germany Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3034257
Heavy, solid cast design Dirt and water-resistant, easy-to-clean membrane keypad 24V DC electronics Machine light Drilling depth stop Solid base plate with precise surface finish Coolant device, chip filter Tapping device Extremely stable, thick-walled cast column Equipment Electrically operated quill feed Oil pump Programmable feed cut-off Easy-to-read digital display Digitally adjustable drilling and thread depth Digital zero point can be set Manufacturer Optimum Maschinen Germany GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@optimum-maschinen.de
Add to compare list Add to wishlist
51-3672220
For comfortable reading of the set values via 1/10 mm LED display Receives the input signals via a magnetized pole ring and a sensor head mounted directly on the drive shaft Measuring accuracy is ± 0.2 mm per meter Easy to read Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3815630
Thin sheets are supported in order to be able to apply dimensionally to the backgauge pneumatic sheet holding device with selector lever for the direction of the sheet metal chute Operator can choose if the section falls into the back room or the operator side Pneumatic sheet support, sheet ejection to the front or rear controllable via toggle switch Backgauge 750 mm guided on round shafts and driven via ball screw Stainless steel table supports with transfer balls for comfortable material handling Positioning control of the backgauge Maper HT071 with digital dimension display Heavy and robust steel construction in welded design Constant, low cutting angle for optimum cutting results Side fence 1000 mm with scale and T-slot Two material support arms 500 mm with T-slot Balls in the support table for easier material transport Cutting gap adjustment by means of vernier rings High quality blade suitable for stainless steel LED illumination of the cutting area Continuous finger protection device Mobile foot pedal with emergency stop switch All moving parts with low-maintenance bearings Electrical system from Siemens and Schneider Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3953613
Extremely stable construction, entire machine body made of steel User-friendly operating concept Speed infinitely variable via inverter - Greater ease of operation and no need to replace wearing parts such as V-belts Combined micro-spray and blow-off device, for blowing off chips and lubricating the saw blade Tiltable working table made of cast iron Workplace lighting as standard Equipped with motor brake Belt tension and speed indicator Integrated band welding unit with annealing, cutting and grinding device Height adjustment of saw band guide by hand wheel VMBS I E models with electric table feed Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3071199
Low-wear brass guide Weldon and MK mount Manufacturer Optimum Maschinen Germany GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@optimum-maschinen.de
Add to compare list Add to wishlist
51-3779121
Powerful and quiet drive via LENZE gear motors with brake Compact, heavy and stress-free welded steel construction Sharp bending rail made of tool steel C50 at the clamping cheek Continuous, exchangeable bed support made of tool steel C50 Continuous bending rail made of tool steel C50 at the bending beam Automatic pressure regulation of the clamping cheek via motor current pick-up Drive of the clamping cheek via generously dimensioned trapezoidal thread spindles Bending angle adjustment PT 1 via potentiometer on the machine front (right) Manual fine adjustment of bending beam with scale Manual crowning via pressure screws in the bending beam Foot remote control with emergency stop function All moving parts with low-maintenance bearings Electrical components from Schneider or Omron SH-models with high, segmented goat's foot tools Quality Made in Europe Available on request: Models in DUO design with continuous sharp bending rail and segmented goad foot tools, standard tools hardened, sharp bending rail and bending bar hardened, segmented tools and bending bar hardened, segmented goad foot tools and bending bar hardened Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3814002
Heavy and stable cast iron construction handy and easy adjustable sub-waves steel shafts adjustable stop plate Please specify when ordering material to be edited!
Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3813202
For use in industry and trade Heavy and stable cast iron construction Asymmetrical 3-roller system Upper roller swung out, thereby easy removal of the finished workpiece Easily adjustable upper and lower roller The foot control leaves both hands free for the material supply User-friendly Powerful 400 volt engine Optionally available: hardened rollers Hints:
When ordering, please specify the type of material to be processed! All accessories only possible ex works. Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3925271
Powerful motor and vibration-free operation for the best sanding results Continuous face sanding surface thanks to removable attachments enables sanding of even long workpieces Quick clamping system enables fast sanding belt changes One extraction nozzle each directly on the spark box and on the rear belt roller Can be used with and without suction Easy adjustment of the belt run via adjusting screw on the front contact roller Automatic retensioning of the sanding belt thanks to spring-loaded belt tensioning system Infinitely tiltable sanding unit Fold-away protective screen Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-4403205
Motorised height adjustment of the work table Conveyor table with profile conveyor belt for optimum stability during transportduring processing NC control with 8" touch screen Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3300080
With high-quality bi-metal band saw blade as standard Adjustable material stop for standard work Push button on the lever arm for the saw blade run switches the saw blade run on and off Base plate with non-slip feet Low-vibration and low-wear thanks to special gearbox with two hardened steel gears Vario drive motor with low speed and carbon brushes for up to 10 times longer service life Saw arm can be tilted from 0° to +60° to enable angled saw cuts Manufacturer Optimum Maschinen Germany GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3812060
Heavy welded steel construction Horizontal and vertical working possibility Hydraulic feed of the upper roller Digital display for feed roller All 3 rollers driven and hardened Lateral straightening rollers, infinitely adjustable Separate control panel with foot control Optional accessory:
Tube bending rolls Angle bending rolls Special straightening rolls Profile bending rolls Plastic rollers for soft materials Notice:
Please indicate the type of material to be processed when ordering! NC-control Art. No. 3880163: Cannot be retrofitted, only for new machine orders! Optionally the machine can be equipped with bending rolls especially for your requirements. Also untypical sizes can be produced on request Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3661328
Stable U-shaped closed construction made of 3 mm sheet steel profile Support rollers made of galvanized steel All roller conveyors of the MRB standard series also available with plastic rollers Supported rollers ball-bearing Feed / discharge roller conveyor Roller conveyor without scale and stop with side guide Quality Made in Germany Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3290361
Heavy industrial version Quiet running Manual or semi-automatic operation Steplessly adjustable saw blade speed from 0-80 m/min. High cutting accuracy due to vibration-free running Mitration adjustment up to 60° by swivelling the entire saw bow Serially equipped with high-quality bi-metalSaw band End stops adjustable down to the degree Swarf brush Microswitch for automatic limit switch Roller support adjustable for long and heavy workpieces Coolant pump Ball bearing mounted Saw blade guide with carbide plates for optimum cutting results Easy adjustment of the lowering speed by means of feed control valve in the control panel Large dimensioned, hydraulic quick-clamping vice, self-closing, adjustable for large cross-sections Completely equipped machine; The user can work productively immediately after commissioning EMV class C2 2-channel safety chain with quick stop in case of emergency Function semi-automatic operation closing the vice and activating the motor lowering the saw bow for cutting stopping the motor and returning the saw bow to the starting position Manufacturer Optimum Maschinen Germany GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@optimum-maschinen.de
Add to compare list Add to wishlist
51-3662250
Roller and guideway system on which lighter wood, metal or plastic profiles can be precisely sawed, drilled or milled Substructure made of solid 3 mm steel profiles, painted and with adjustable feet Support rollers made of galvanized steel (optionally also available with plastic rollers) Stop track with length stop, manual measuring system with mm scale and reading magnifier Stop car is 4-roller bearings, thus manually easily displaced Adjustable stop arm and can be folded away to the rear Maximum measuring length is the length of the web minus the stop length of 250 mm Quality Made in Germany Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3779052
Semi-motor version - manual operation of the upper cheek, bending process motorised Designed for professional use With foot operation heavy, compact weldment With continuous sharp bending rail Standard with manual adjustment of the bending angle by means of nonius ring Particularly low-maintenance S-models with segmented top tools SH models with high, segmented goat foot tools Hardening of standard tools available on request: sharp bending rail and bending strip hardened, segmented tools and bending strip hardened, segmented goat foot tools and bending strip hardened Further swivel bending machines available on request Quality Made in Europe
Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3662440
Roller and guideway system on which lighter wood, metal or plastic profiles can be precisely sawed, drilled or milled Substructure made of solid 3 mm steel profiles, painted and with adjustable feet Support rollers made of galvanized steel (optionally also available with plastic rollers) With length stop, magnetic tape measuring system with digital display, measuring accuracy +/- 0.2 mm per meter Stop car is 4-roller bearings, thus manually easily displaced Adjustable stop arm and can be folded away to the rear The maximum measuring length is the length of the web minus the stop length of 250 mm Quality Made in Germany Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3661214
Stable U-shaped closed construction made of 3 mm sheet steel profile Support rollers made of galvanized steel All roller conveyors of the MRB standard series also available with plastic rollers Supported rollers ball-bearing The maximum measuring length is the length of the track minus the stop length 260 mm With length measuring device Roller and measuring track with mm-scale, manual measuring system with C-guide profile and sliding flap stop Quality Made in Germany Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
Add to compare list Add to wishlist
51-3923141SET
Changing the sanding belt in seconds due to the quick-release system Automatic re-tensioning of the sanding belt using the spring-loaded belt tensioning system Easy adjustment of the belt run using the adjusting screw Can be used as a table model and also as a standing model with the optional base Powerful motors and vibration-free operation for the best sanding results Sanding belt can be changed in seconds thanks to the quick-clamping system Automatic retensioning of the sanding belt thanks to spring-loaded belt tensioning system Large surface sanding area thanks to fold-away upper sanding belt cover Easy adjustment of the belt tracking via adjusting screw on the front contact roller Continuous sanding surface after removal of attachments enables sanding of long workpieces as well Can be used with and without suction One extraction nozzle on the spark box and one on the rear belt roller Protective screen can be folded away Can be used as a table model and, with the optional base, also as a floor model Manufacturer Stürmer Maschinen GmbH
Dr.-Robert-Pfleger-Str. 26, 96103 Hallstadt, Germany
info@stuermer-maschinen.de
