The two-stage compression 2-cylinder high-performance unit achieves a very low rotational speed, resulting in a particularly quiet and low-vibration run
This ensures a longer life due to less wear
Large fan wheel and a cooling air baffle on the cylinder for optimum cooling of the compressor
Aftercooler with cooling fins and intercooler to the aftercooler ensure a low container inlet temperature and thus less moisture in the compressed air
High quality electric motor with high torque
Electric motor equipped with motor protection switch
With high-quality CONDOR pressure switch
Equipped with a pressure gauge for tank pressure and a ball valve on the compressed air tank
Compressed air tank equipped with safety valve, container pressure gauge and condensate drain tap
Ten-year rust-through warranty on powder-coated compressed air tank
With all safety devices
Fully wired
Stable belt guard made of metal
Including swinging elements
Connection to grid by qualified electrician
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
With star-delta switch
High cooling effect and lower noise level due to thermostatically controlled radial fan
Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirement via automatic message
Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
Screw compressor with wear-resistant Poly V ribbed belt drive and carriage tensioning system
Easy maintenance due to easily accessible elements
Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
Small external dimensions, thus easy transport and installation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Sintered filter with centrifugal principle, diaphragm pressure regulator with secondary venting and normal mist lubricator with post-suction device under pressure
For compressed air and neutral gases
Filter pressure regulator with semi-automatic condesate drain
Secured via lockable handwheel
For vertical installation
Sintered filter with centrifugal principle, diaphragm pressure regulator with secondary venting and normal mist lubricator with suction device under pressure
For compressed air and neutral gases
Filter pressure regulator with semi-automatic condesate drain
Safety via lockable handwheel
Fog lubricator for oil type CL 32 according to DIN 51517-ISO VG 32 - oil refill under pressure up to max. 10 bar possible
Input pressure 1, 5 - 16 bar
Suitable for temperatures from -10 to +50°C
For vertical installation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Large fan wheel and a cooling air baffle on the cylinder for optimum cooling of the compressor
Aftercooler with cooling fins for low vessel inlet temperature and less moisture in the compressed air
Sturdy metal belt guard
"Made in Germany": vessel pressure gauge; filter pressure regulator with pressure gauge for regulated compressed air cleaned of condensate, dirt and oil
Ten-year warranty against rust-through on powder-coated compressed air reservoir
Including high-quality composite safety coupling and high-quality CONDOR pressure switch
Two-cylinder high-performance units made of gray cast iron for a long service life.
Large fan wheel and a cooling air baffle on the cylinder for optimal cooling of the compressor
Quality electric motor with high starting torque
Electric motor equipped with motor protection switch
Aftercooler with cooling fins ensures a low tank inlet temperature and thus less moisture in the compressed air
Sturdy metal belt guard
Start-up capacitor and start-up relief valve ensure easy start-up on 230 volt models
Container pressure gauge "Made in Germany
Filter pressure regulator with pressure gauge "Made in Germany" for regulated compressed air cleaned of condensate, dirt and oil
Ten-year warranty against rust-through on powder-coated compressed air reservoir
Includes high quality composite safety coupling and high quality CONDOR pressure switch
Large ergonomic handle
Stable steering chassis with parking brake in combination with large, puncture-proof PU wheels
Made in Europe
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
The two-stage, high performance, 2-cylinder unit provides very low RPM for smooth, low-vibration operation
Large fan for optimal cooling
Between- and aftercooler for a low tank inlet temperature and reduction of condensation
High quality electric motors equipped with motor protection switch
Ready for connection with all fittings such as safety valve and check valve, condensate and air release valve for autonomous operation
Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
High quality CONDOR pressure switch for fully automatic on-off operation
Flexible armored hose line with heat protection prevents vibration break
Compressor compressors are used when:
the available air volume is too small
Peak performance needs to be met
10 0% safety must be warrantyd
Old equipment would require expensive repairs
We save for you - 13 bar instead of 15 bar!
Our 15 bar compressors are factory set to 13 bar shutdown pressure. The reason for this is that, according to experience, 90% of all users have an operating pressure of max. 13 bar
Any additional pressure generated means an energy consumption of about 8% per bar.
If you still need the maximum pressure of 15 bar, you can easily do it yourself at any time at the pressure switch.
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Flow-optimized air supply for up to 75% less resistance
Assembly of the filter elements without cross-sectional narrowing and disturbing tie rods, thus reduced flow resistance and easy element change even in confined spaces
Cavity volume of the borosilicate filter material of 96% ensures the lowest pressure loss
CLEARPOINT® filter housing made of water-resistant aluminum and additionally anodised on the inside, therefore increased operational safety and reduced flow resistance due to permanently smooth inner surfaces
100% control when opening the filter housing by a secure locking mechanism, when opened under pressure a warning signal sounds
With thermally highly resistant (up to 120 ° C), mechanically highly resistant, chemically resistant and silicone-free needle felt drainage layer (in contrast to foam material of other filter makes)
Stable construction of the filter element - it is not possible to inflate or rupture the drainage layer, thereby ensuring the constant use of the entire filter surface
for the separation of oil vapors, odors and flavorings via adsorption and in the second stage of solid particles
Residual content of oil vapor up to 0.003 mg / m³ at 20 ° C and 1 bar
absolute compressed air quality according to ISO 8573-1
For compressed air of the highest quality, eg, for breathing air, in analytical technology or semi-luxury bottling
Pure compressed air in connection with upstream ultrafine filter
Flow-optimized air supply for up to 75% less resistance
Assembly of the filter elements without cross-sectional narrowing and disturbing tie rods, thus reduced flow resistance and easy element change even in confined spaces
Cavity volume of the borosilicate filter material of 96% ensures the lowest pressure loss
CLEARPOINT® filter housing made of water-resistant aluminum and additionally anodised on the inside, therefore increased operational safety and reduced flow resistance due to permanently smooth inner surfaces
100% control when opening the filter housing by a secure locking mechanism, when opened under pressure a warning signal sounds
With thermally highly resistant (up to 120 ° C), mechanically highly resistant, chemically resistant and silicone-free needle felt drainage layer (in contrast to foam material of other filter makes)
Stable construction of the filter element - it is not possible to inflate or rupture the drainage layer, thereby ensuring the constant use of the entire filter surface
for the separation of oil vapors, odors and flavorings via adsorption and in the second stage of solid particles
Residual content of oil vapor up to 0.003 mg / m³ at 20 ° C and 1 bar
absolute compressed air quality according to ISO 8573-1
For compressed air of the highest quality, eg, for breathing air, in analytical technology or semi-luxury bottling
Pure compressed air in connection with upstream ultrafine filter
Innovative LOGIN control with 4.3" touch screen for easy operation and full control of all functions.
Rotation direction control for the motor, prevents damage during start-up or after a change of location
High cooling effect and low noise level due to thermostatically controlled radial fan
Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled centrifugal fan, optimum cooling air flow and generously dimensioned heat exchangers
Aftercooler reduces the effort for drying and filtration of the generated compressed air
Easy to service: simple removal and installation of all components requiring maintenance
Latest generation IE4 permanent magnet motor for max. energy efficiency
Larger speed/load range
Larger delivery volume supply range
Extremely energy efficient - up to 50% energy consumption savings compared to a "fixed speed" model
Very quiet operation - only 64 dB
Energy saving through frequency control
Ideal for frequently changing compressed air consumption
Compressor delivery rate adjusts to actual consumption
Electronic control monitors motor and compressor speed and keeps line pressure constant even when consumption fluctuates widely
Advanced and efficient cutting-edge technology in the smallest possible space
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
