Two-stage compression 2-cylinder high-performance unit with cast iron cylinder block
The low speed ensures quiet, low-vibration operation and a long service life
Large fan wheel for optimal cooling
High quality electric motor with high torque
Electric motor equipped with motor protection switch
With phase inverter for easy manual reversal of the direction of rotation
Intermediate and aftercooler reduces the formation of condensation
Maintenance block with two pressure gauges for tank pressure and working pressure and high quality CONDOR pressure switch
Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
Fully automatic on-off operation
Ready for connection with all fittings
Increased flexibility
By connecting the second compressed air tank, the container volume is doubled, whereby a higher air supply can be established
An increased demand for air can thus be covered in the short term.
The second compressed air tank can be disconnected from the compressed air supply e.g. for chiselling or sandblasting. This halves the container volume and pressure builds up faster.
Equipment details:
K version with refrigeration dryer with integrated automatic steam trap as standard
Pressure dew point 5 °C, compressed air inlet temperature 35 °C, cooling air temperature 25 °C
K version additionally with pre-filter for separating condensate and solid impurities with particles up to 1 μm
Compressed air quality according to ISO 8573-1
As a pre-filter in front of the refrigeration dryer
KK version with automatic steam trap on the compressed air tank
This condensate drainage without unnecessary pressure loss
Condensate conditioner for oil-water separation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Maximum, robust equipment and best quality at a reasonable price
Fully automatic on-off operation
With all safety devices
Completely ready for connection
Quality electric motor
Quality electric motor with high starting torque is equipped with a motor protection switch
Starting capacitor and starting relief valve ensure easy starting
Phase inverter as standard for easy manual reversal of the direction of rotation
Compressed air compression via high-performance HOS unit
The start-up relief valve ensures easy and pressureless start-up
The two-cylinder high-performance unit made of gray cast iron and the low speed guarantee particularly quiet and low-vibration running and a long service life
This ensures an even longer service life due to even less wear and tear
High-quality compressor with optimum lubrication for a long service life and high reliability
Equipped with high quality intake filter
The aftercooler with large cooling fins ensures a low boiler inlet temperature and thus less moisture in the compressed air, which protects the air tools
Additional intercooler to the aftercooler
Corrosion-free valve plates for improved heat dissipation and compressor longevity
The large fan impeller and a cooling air baffle on the cylinder ensure optimum cooling of the compressor
A sturdy metal belt guard ensures optimum protection of the components and a high level of user safety
Compressed air supply to the boiler via flexible armored hose line with heat protection prevents vibration breakage
High quality drive belt
Powerful and economical drive
The toothed drive belt facilitates start-up, improves running smoothness and power transmission and reduces power consumption by up to 30%.
Sturdy metal belt guard
Operation on the maintenance block
Equipped with a high-quality CONDOR MDR 5 pressure switch with robust push-button function for fully automatic on-off operation
Filter pressure regulator for stepless adjustment of the working pressure, with simultaneous separation of dirt, oil and condensation water
Two large pressure gauges indicate the tank pressure and the working pressure
Air extraction at the maintenance block via a comfort safety quick coupling
Only fixed screw connections at the maintenance block, no hose connections
Two compressed air tapping points
One compressed air tapping point for filtered compressed air
One compressed air tapping point via direct outlet on the boiler with ball valve
Comfort safety coupling - The advantages.
Comfort safety couplings from AIRCRAFT as the first manufacturer used in series production
Two separate locking systems for maximum working safety
Dangerous whipping of the hose line is prevented
Comfortable and safe to transport and set up
Ergonomically extended handle for comfortable transport in an almost upright position - strain on the back due to lifting is avoided
Puncture-proof PU foam wheels and stable steering chassis with parking brake allow easy transport
The parking brake prevents both turning and rolling movement of the wheels and ensures an optimal stand of the compressor
With practical second transport handle on the boiler, which makes carrying the compressor easier
High quality boiler with durable rust protection
AIRCRAFT is the first manufacturer to equip the AIRPROFI series compressors with hot-dip galvanized boilers inside and outside as standard
AIRPROFI series boilers therefore come with a 15-year warranty against rusting through.
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
High cooling effect and lower noise level due to thermostatically controlled radial fan
Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirements via automatic message
Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
Screw compressor with wear-resistant Poly V ribbed belt drive and slide clamping system
Easy maintenance due to easily accessible elements
Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
Small external dimensions, thus easy transport and installation
Energy savings through frequency-controlled compressors
Reducing energy consumption and protecting our precious energy resources has become a global challenge given its impact on the environment. The A-PLUS range, with outputs of 22, 37, 55 and 75 kW, is also available in a speed control version that combines high performance with energy saving solutions. By using a variable speed compressor in a typical installation, you save a significant amount of energy.
A frequency converter dynamically adjusts the voltage, frequency and current values of the motor. The air output is constantly set to 50 to 100 percent of the full load of the compressor. This gives the following measurable positive effects:
Accurate coverage of the air requirement by continuous control of the engine speed and compressed air generation
Minimization of unnecessary energy losses by continuous adjustment of the compressed air generation to the actual air requirement
Energy consumption proportional to the supplied compressed air
Constant and precise pressure control, adjustable to any value between 6 and 10 bar (13 bar on request)
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Flow-optimized air supply for up to 75% less resistance
Assembly of the filter elements without cross-sectional narrowing and disturbing tie rods, thus reduced flow resistance and easy element change even in confined spaces
Cavity volume of the borosilicate filter material of 96% ensures the lowest pressure loss
CLEARPOINT® filter housing made of water-resistant aluminum and additionally anodised on the inside, therefore increased operational safety and reduced flow resistance due to permanently smooth inner surfaces
100% control when opening the filter housing by a secure locking mechanism, when opened under pressure a warning signal sounds
With thermally highly resistant (up to 120 ° C), mechanically highly resistant, chemically resistant and silicone-free needle felt drainage layer (in contrast to foam material of other filter makes)
Stable construction of the filter element - it is not possible to inflate or rupture the drainage layer, thereby ensuring the constant use of the entire filter surface
for the separation of oil vapors, odors and flavorings via adsorption and in the second stage of solid particles
Residual content of oil vapor up to 0.003 mg / m³ at 20 ° C and 1 bar
absolute compressed air quality according to ISO 8573-1
For compressed air of the highest quality, eg, for breathing air, in analytical technology or semi-luxury bottling
Pure compressed air in connection with upstream ultrafine filter
The two-stage compression 2-cylinder high-performance unit enables a very low speed, resulting in a particularly quiet and low-vibration run
Large fan ensures optimal cooling
Intercooler and aftercooler ensure a low container inlet temperature and thus reduce condensation
High quality electric motor with high torque
Electric motor equipped with motor protection switch
Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
Flexible armored hose line with heat protection prevents vibration breakage
High-quality CONDOR pressure switch as standard
From 7.5 kW as standard with star-delta switch with operating hours counter
Ready for connection with all fittings
Additional equipment K-version:
Refrigerated dryer with integrated automatic steam trap for dry compressed air, longer service life of compressed air tools and avoidance of disturbances in pneumatic controls
Fine filter for separating condensate and solid impurities with particles up to 1 μ in front of the refrigeration dryer
Equipment
Automatic steam trap on the compressed air tank
No unnecessary pressure loss
Condensate conditioner for oil-water separation
Important notes on condensate treatment can also be found in the section on compressed air preparation.
Fine filter for separating condensate and solid impurities with particles up to 1 μm
Compressed air quality according to ISO 8573-1
As a pre-filter in front of the refrigeration dryer
Refrigerated dryer with integrated automatic steam trap
Pressure dew point at 5 °C, ambient temperature 25 °C, atmospheric dew point at -22 °C
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Innovative LOGIN control with 4.3" touch screen for easy operation and full control of all functions.
Rotation direction control for the motor, prevents damage during start-up or after a change of location
High cooling effect and low noise level due to thermostatically controlled radial fan
Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled centrifugal fan, optimum cooling air flow and generously dimensioned heat exchangers
Aftercooler reduces the effort for drying and filtration of the generated compressed air
Easy to service: simple removal and installation of all components requiring maintenance
Latest generation IE4 permanent magnet motor for max. energy efficiency
Larger speed/load range
Larger delivery volume supply range
Extremely energy efficient - up to 50% energy consumption savings compared to a "fixed speed" model
Very quiet operation - only 64 dB
Energy saving through frequency control
Ideal for frequently changing compressed air consumption
Compressor delivery rate adjusts to actual consumption
Electronic control monitors motor and compressor speed and keeps line pressure constant even when consumption fluctuates widely
Advanced and efficient cutting-edge technology in the smallest possible space
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Innovative LOGIN control with 4.3" touch screen for easy operation and complete control over all functions
Connection of up to eight compressors possible, no matter if with constant or variable speed
All information on current operating status at a glance
Rotation direction control for the motor, prevents damage during start-up or after a change of location
Low noise emission (only max. 67 dB) during operation, due to extremely low speed of the screw compressor and use of a low-noise radial fan
Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled centrifugal fan, optimum cooling air flow and generously dimensioned heat exchangers
Aftercooler reduces the effort for drying and filtration of the generated compressed air
Star-delta switching as standard
Easy to service: simple removal and installation of all components requiring maintenance
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
