For continuous air demand and discontinuation operation
Electronic control for reliability and efficiency
Increased flexibility thanks to two compressed air tanks
High-quality and expandable equipment
Smooth and quiet
Just as mobile and compact as piston compressors, but with the great advantage of being able to generate compressed air continuously without any cooling pauses
Can also be used in intermittent operation due to oil temperature control
Electronic temperature control for optimum oil temperature
Optimum oil viscosity due to constant temperature, therefore also suitable for intermittent operation with frequent load changes
Temperature control of the oil prevents condensation and minimizes wear
Better energy efficiency compared to a piston compressor with the same delivery capacity
Additional oil heat exchanger for cooling
K-Tronic electronic control system for reliability and efficiency
Adjustment of the cut-in and cut-out pressure
Direction of rotation control
Monitoring and control of the oil temperature
Maintenance interval display
Optimized oil separation system
Effective oil pre-separation by gravity, as the oil sump is located at the lowest point
Oil separator cartridge and oil filter cartridge easily accessible for maintenance
Integrated design of the compressor unit
Convenience and high operational reliability thanks to integration and short connections of all key components on the compressor unit
Maintenance-free direct drive
Freewheel valve for load-free operation after reaching the set pressure
Lightweight, compact and quiet
Can be used in mobile applications or where space is limited
Highly efficient and low-noise fan
Smooth-running compressor with low noise level
Increased flexibility thanks to two compressed air tanks
Two 100 liter compressed air tanks ready mounted on a safety pallet
Doubling of the air supply by switching on the second compressed air tank - an increased air requirement is covered at short notice
Halving the tank volume by disconnecting the second compressed air tank - allows pressure to be built up quickly, e.g. for chiseling or sandblasting work
High-quality equipment
Hot-dip galvanized compressed air tanks inside and out with a 15-year guarantee against rusting through
Splash water protection in accordance with IP 54
Flexible armored hose lines with heat protection prevent vibration fractures
With phase inverter on the plug as standard
Ready for connection with all fittings
Additional equipment for compressed air preparation and discharge available
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Innovative LOGIN control with 4.3" touch screen for easy operation and full control of all functions.
Rotation direction control for the motor, prevents damage during start-up or after a change of location
High cooling effect and low noise level due to thermostatically controlled radial fan
Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled centrifugal fan, optimum cooling air flow and generously dimensioned heat exchangers
Aftercooler reduces the effort for drying and filtration of the generated compressed air
Easy to service: simple removal and installation of all components requiring maintenance
Latest generation IE4 permanent magnet motor for max. energy efficiency
Larger speed/load range
Larger delivery volume supply range
Extremely energy efficient - up to 50% energy consumption savings compared to a "fixed speed" model
Very quiet operation - only 64 dB
Energy saving through frequency control
Ideal for frequently changing compressed air consumption
Compressor delivery rate adjusts to actual consumption
Electronic control monitors motor and compressor speed and keeps line pressure constant even when consumption fluctuates widely
Advanced and efficient cutting-edge technology in the smallest possible space
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Two-stage compression 2-cylinder high-performance unit with cast iron cylinder block
The low speed ensures quiet, low-vibration operation and a long service life
Large fan wheel for optimal cooling
High quality electric motor with high torque
Electric motor equipped with motor protection switch
With phase inverter for easy manual reversal of the direction of rotation
Intermediate and aftercooler reduces the formation of condensation
Maintenance block with two pressure gauges for tank pressure and working pressure and high quality CONDOR pressure switch
Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
Fully automatic on-off operation
Ready for connection with all fittings
Increased flexibility
By connecting the second compressed air tank, the container volume is doubled, whereby a higher air supply can be established
An increased demand for air can thus be covered in the short term.
The second compressed air tank can be disconnected from the compressed air supply e.g. for chiselling or sandblasting. This halves the container volume and pressure builds up faster.
Equipment details:
K version with refrigeration dryer with integrated automatic steam trap as standard
Pressure dew point 5 °C, compressed air inlet temperature 35 °C, cooling air temperature 25 °C
K version additionally with pre-filter for separating condensate and solid impurities with particles up to 1 μm
Compressed air quality according to ISO 8573-1
As a pre-filter in front of the refrigeration dryer
KK version with automatic steam trap on the compressed air tank
This condensate drainage without unnecessary pressure loss
Condensate conditioner for oil-water separation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
High cooling effect and lower noise level due to thermostatically controlled radial fan
Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirements via automatic message
Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
Screw compressor with wear-resistant Poly V ribbed belt drive and slide clamping system
Easy maintenance due to easily accessible elements
Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
Small external dimensions, thus easy transport and installation
Energy savings through frequency-controlled compressors
Reducing energy consumption and protecting our precious energy resources has become a global challenge given its impact on the environment. The A-PLUS range, with outputs of 22, 37, 55 and 75 kW, is also available in a speed control version that combines high performance with energy saving solutions. By using a variable speed compressor in a typical installation, you save a significant amount of energy.
A frequency converter dynamically adjusts the voltage, frequency and current values of the motor. The air output is constantly set to 50 to 100 percent of the full load of the compressor. This gives the following measurable positive effects:
Accurate coverage of the air requirement by continuous control of the engine speed and compressed air generation
Minimization of unnecessary energy losses by continuous adjustment of the compressed air generation to the actual air requirement
Energy consumption proportional to the supplied compressed air
Constant and precise pressure control, adjustable to any value between 6 and 10 bar (13 bar on request)
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
The two-stage compression 2-cylinder high-performance unit enables a very low speed, resulting in a particularly quiet and low-vibration run
Large fan ensures optimal cooling
Intercooler and aftercooler ensure a low container inlet temperature and thus reduce condensation
High quality electric motor with high torque
Electric motor equipped with motor protection switch
Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
Flexible armored hose line with heat protection prevents vibration breakage
High-quality CONDOR pressure switch as standard
From 7.5 kW as standard with star-delta switch with operating hours counter
Ready for connection with all fittings
Additional equipment K-version:
Refrigerated dryer with integrated automatic steam trap for dry compressed air, longer service life of compressed air tools and avoidance of disturbances in pneumatic controls
Fine filter for separating condensate and solid impurities with particles up to 1 μ in front of the refrigeration dryer
Equipment
Automatic steam trap on the compressed air tank
No unnecessary pressure loss
Condensate conditioner for oil-water separation
Important notes on condensate treatment can also be found in the section on compressed air preparation.
Fine filter for separating condensate and solid impurities with particles up to 1 μm
Compressed air quality according to ISO 8573-1
As a pre-filter in front of the refrigeration dryer
Refrigerated dryer with integrated automatic steam trap
Pressure dew point at 5 °C, ambient temperature 25 °C, atmospheric dew point at -22 °C
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
