Flow-optimized air supply for up to 75% less resistance
Assembly of the filter elements without cross-sectional narrowing and disturbing tie rods, thus reduced flow resistance and easy element change even in confined spaces
Cavity volume of the borosilicate filter material of 96% ensures the lowest pressure loss
CLEARPOINT® filter housing made of water-resistant aluminum and additionally anodised on the inside, therefore increased operational safety and reduced flow resistance due to permanently smooth inner surfaces
100% control when opening the filter housing by a secure locking mechanism, when opened under pressure a warning signal sounds
With thermally highly resistant (up to 120 ° C), mechanically highly resistant, chemically resistant and silicone-free needle felt drainage layer (in contrast to foam material of other filter makes)
Stable construction of the filter element - it is not possible to inflate or rupture the drainage layer, thereby ensuring the constant use of the entire filter surface
for the separation of oil vapors, odors and flavorings via adsorption and in the second stage of solid particles
Residual content of oil vapor up to 0.003 mg / m³ at 20 ° C and 1 bar
absolute compressed air quality according to ISO 8573-1
For compressed air of the highest quality, eg, for breathing air, in analytical technology or semi-luxury bottling
Pure compressed air in connection with upstream ultrafine filter
Compressed air filters are used for highly efficient removal of solid particles, water, oil, aerosols, hydrocarbons, odors and vapors from compressed air systems.
To achieve the required quality of compressed air, filters that gradually remove all types of solid and liquid contaminants from the compressed air must be installed in the compressed air line
Your advantages through better quality compressed air:
Safe filtration of both liquids such as water and aerosols as well as particles, dust and gases
Better working and production conditions
Optimum protection of connected tools and machines
Improved product quality through reduction of rejects
Protection of the compressed air system against contamination
Increase of productivity by reduction of instant maintenance
for separating solid contaminants up to 0.01μm
Residual oil aerosol content up to 0.01 mg / m³ at 20 ° C and 1 bar
Operating temperature 1.5 to 65 ° C
absolute compressed air quality according to ISO 8573-1
for safe separation of condensate and particles
complete with filter element and float valve
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Sintered filter with centrifugal principle, diaphragm pressure regulator with secondary venting and normal mist lubricator with post-suction device under pressure
For compressed air and neutral gases
Filter pressure regulator with semi-automatic condesate drain
Secured via lockable handwheel
For vertical installation
Sintered filter with centrifugal principle, diaphragm pressure regulator with secondary venting and normal mist lubricator with suction device under pressure
For compressed air and neutral gases
Filter pressure regulator with semi-automatic condesate drain
Safety via lockable handwheel
Fog lubricator for oil type CL 32 according to DIN 51517-ISO VG 32 - oil refill under pressure up to max. 10 bar possible
Input pressure 1, 5 - 16 bar
Suitable for temperatures from -10 to +50°C
For vertical installation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
With star-delta switch
High cooling effect and lower noise level due to thermostatically controlled radial fan
Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirements via automatic message
Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
Screw compressor with wear-resistant Poly V ribbed belt drive and slide clamping system
Easy maintenance due to easily accessible elements
Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
Small external dimensions, thus easy transport and installation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
All main components of the compressor are manufactured by machining using numerically controlled machine tools, including suction regulator, separator block and minimum pressure valve
The cooling takes place via a temperature-controlled centrifugal fan and an oversized combination cooler. This ensures optimal cooling even under the most extreme conditions.
Generous access panels allow easy maintenance and immediate control of the internal components, reducing the time required for inspection and maintenance to one medium.
The main operating parameters are monitored by the electronic microprocessor control NRG: In addition to the various functions, a weekly timer for switching on and off is available to meet the requirements of each customer. In addition, up to 4 machines can be controlled simultaneously according to the master / slave principle.
Standard with star-delta connection
Energy savings through frequency-controlled compressors Reducing energy consumption and protecting our precious energy resources has become a global challenge given its impact on the environment. The A-PLUS 22, 37, 55 and 75 kW range is also available in a speed control version that combines high performance with energy saving solutions. By using a variable speed compressor in a typical installation, you save a significant amount of energy. Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
All main components of the compressor are manufactured by machining using numerically controlled machine tools, including suction regulator, separator block and minimum pressure valve
The cooling takes place via a temperature-controlled centrifugal fan and an oversized combination cooler. This ensures optimal cooling even under the most extreme conditions.
Generous access panels allow easy maintenance and immediate control of the internal components, reducing the time required for inspection and maintenance to one medium.
The main operating parameters are monitored by the electronic microprocessor control NRG: In addition to the various functions, a weekly timer for switching on and off is available to meet the requirements of each customer. In addition, up to 4 machines can be controlled simultaneously according to the master / slave principle.
Standard with star-delta connection
Energy savings through frequency-controlled compressors Reducing energy consumption and protecting our precious energy resources has become a global challenge given its impact on the environment. The A-PLUS 22, 37, 55 and 75 kW range is also available in a speed control version that combines high performance with energy saving solutions. By using a variable speed compressor in a typical installation, you save a significant amount of energy. Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
