Basic fitting kit Basic set of fittings 1 "from 1000 l, 11 bar

• Simple and quick installation
• Ideal for compressed air and liquids
• Can be assembled without tools
• Fast, multiple disconnections possible
• Very good flow properties

Manufacturer
Reliance Worldwide Distribution (Europe) Limited
Ludwig-Erhard-Allee 30, 33719 Bielefeld, Germany
www.johnguest.com

• Hot-dip galvanised inside and outside with fifteen-year warranty against rusting through
• Built according to EC Directive 87/404/EEC or DGRL 97/23/EC -AD 2000, module: H / H 1

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• The two-stage compression 2-cylinder high-performance unit enables a very low speed, resulting in a particularly quiet and low-vibration run.
• The large fan ensures optimal cooling.
• Intercooler and aftercooler ensure a low container inlet temperature and thus reduce condensation.
• Quality electric motors equipped with motor protection switch
• Ready for connection with all fittings such as pressure switch for fully automatic on-off operation, safety and check valve, condensate and air release valve for autonomous operation
• Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
• With high-quality CONDOR pressure switch
• Ready for connection with all fittings

Room amenities

• High-performance gray cast iron unit with low speed
• Aftercooler with large cooling fins ensures low tank inlet temperature
• The flexible armored hose line with heat protection prevents a vibration break.

Side compressors are used

• if the existing air volume is too small.
• when peak loads have to be covered.
• if 100% safety must be warrantyd.
• if old equipment would require expensive repairs.

Recommended accessories

• AIRCRAFT tank batteries as 2 or 4 batteries for up to 400 liters additional air reserve

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Ideal in combination with prefabricated solutions
• Permanently sealed without pressing
• Installation even in confined spaces
• Detachable fittings can be reused
• Cost savings through quick assembly

• Permanently sealed without pressing
• Cost savings through quick and easy assembly
• Ideal in combination with prefabricated solutions
• Compatible with other standards-compliant pipes
• No confusion of contours possible
• Installation even in confined spaces
• Extraction forces far beyond the requirements of the standard
• Pipe components can be dismantled and reused
• Numerous national and international approvals
• O-rings included

Manufacturer
Aalberts integrated piping systems B.V.
Oude Amersfoortseweg 99, 1212 NL Hilversum, Netherlands
www.aalberts-ips.com

Advantages of DRYPOINT eco control

• Integrated DRYPOINT M Plus solution: filtration and dryer in a compact form, as well as condensate drain integrated
• Filtration on the spot in the treatment chain where the highest efficiency is achieved
• Easy maintenance / replacement of filter element as with a filter
• Application-specific degree of dryness can be selected
• Consistent compressed air quality under fluctuating operating conditions
• Energy saving through minimization of purging air consumption for actual amount of useful air and degree of drying
• Power evaluation via LED, forwarding via current output 4 … 20 mA possible
• User-friendly: Easy to use, test functions, error messages
• Concept based on the fail-safe principle, error message can be picked up via potential-free contact

Functionality of the DRYPOINT® M eco control

Based on the measurement result from the sensor, the control software decides in defined cycles whether and how long the full amount of purge air has to be provided to achieve and stabilize the required degree of dryness. This process is implemented by means of a targeted clocking of a solenoid valve. In each cycle, the duration of the two process sections described below varies in order to keep the degree of drying within the specified tolerance range.

Manufacturer
BEKO Technologies GmbH
Im Taubental 7, 41468 Neuss, Germany
www.beko.de