Недавно просмотренные товары
52-2048000
- 99% separation of the precipitated condensate directly after the compressor
- For separating large amounts of condensate (water, oil) and dirt particles by centrifugal acceleration of the compressed air
- Use on aftercoolers and refrigeration dryers
- High quality corrosion protection through complete anodization
- Low-flow housing made of seawater-resistant aluminum
- Outside additionally powder-coated
- Differential pressure < 0.06 bar
- With BEKOMAT® steam trap
ManufacturerBEKO Technologies GmbH
Im Taubental 7, 41468 Neuss, Germany
www.beko.de
52-2150002
- Wired remote control for AIRCRAFT energy saver Art. 2150001 and 2150003
- Including 5 m cable
Note: The electrical connection must be made by a licensed company or by purchasing a new energy saver by factory assembly.
ManufacturerAircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at
52-2150031
- Ideal in combination with prefabricated solutions
- Permanently sealed without pressing
- Installation even in confined spaces
- Detachable fittings can be reused
- Cost savings through quick assembly
- Permanently sealed without pressing
- Cost savings through quick and easy assembly
- Ideal in combination with prefabricated solutions
- Compatible with other standards-compliant pipes
- No confusion of contours possible
- Installation even in confined spaces
- Extraction forces far beyond the requirements of the standard
- Pipe components can be dismantled and reused
- Numerous national and international approvals
- O-rings included
ManufacturerAalberts integrated piping systems B.V.
Oude Amersfoortseweg 99, 1212 NL Hilversum, Netherlands
www.aalberts-ips.com
52-2092424
- EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
- With star-delta switch
- High cooling effect and lower noise level due to thermostatically controlled radial fan
- Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirement via automatic message
- Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
- Screw compressor with wear-resistant Poly V ribbed belt drive and carriage tensioning system
- Easy maintenance due to easily accessible elements
- Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
- Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
- Small external dimensions, thus easy transport and installation
ManufacturerAircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at
52-2007430
- Large fan wheel and a cooling air baffle on the cylinder for optimum cooling of the compressor
- Aftercooler with cooling fins for low vessel inlet temperature and less moisture in the compressed air
- Sturdy metal belt guard
- "Made in Germany": vessel pressure gauge; filter pressure regulator with pressure gauge for regulated compressed air cleaned of condensate, dirt and oil
- Ten-year warranty against rust-through on powder-coated compressed air reservoir
- Including high-quality composite safety coupling and high-quality CONDOR pressure switch
- Two-cylinder high-performance units made of gray cast iron for a long service life.
- Large fan wheel and a cooling air baffle on the cylinder for optimal cooling of the compressor
- Quality electric motor with high starting torque
- Electric motor equipped with motor protection switch
- Aftercooler with cooling fins ensures a low tank inlet temperature and thus less moisture in the compressed air
- Sturdy metal belt guard
- Start-up capacitor and start-up relief valve ensure easy start-up on 230 volt models
- Container pressure gauge "Made in Germany
- Filter pressure regulator with pressure gauge "Made in Germany" for regulated compressed air cleaned of condensate, dirt and oil
- Ten-year warranty against rust-through on powder-coated compressed air reservoir
- Includes high quality composite safety coupling and high quality CONDOR pressure switch
- Large ergonomic handle
- Stable steering chassis with parking brake in combination with large, puncture-proof PU wheels
- Made in Europe
ManufacturerAircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at
