Недавно просмотренные товары
52-2500822
- Compressed air tank according to AD 2000 / without fitting set / 11 and 16 bar
- Hot dip galvanized inside and outside
- Constructed in accordance with EC Directive 87/404 / EEC or PED 97/23 / EC -AD 2000, Module: H / H 1
- Operating conditions according to AD 2000 - S1 (10/2000) = arrivals and departures and 20% pressure fluctuation range
- ISO 9001:2015 certified manufacturer
ManufacturerMaschinen- und Behälterbau GmbH
Betzdorfer Straße 170, 57567 Daaden, Germany
www.mabe.de
52-2505649
Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at
52-2091662
- Screw compressor with ribbed belt drive
- Start-stop operation via pressure switch, thereby saving energy compared to idling control
- Minimal and easy maintenance
- Ready for connection with all fittings
- Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
- Easily transportable and deployable thanks to the safety pallet.
- KK version as standard with automatic steam trap for the reliable and economical discharge of the condensate without unnecessary loss of compressed air
- K and KK version with refrigeration dryer as standard with pressure dew point at 3 °C, ambient temperature 25 °C
Increased flexibility- Enabling the second compressed air vessel doubles the pressure vessel volume, thus creating a greater compressed air reserve. Helps to cover short-term peaks in compressed air requirements
- For, e.g., chisel, hammer or sandblasting work, the second vessel can be isolated from the compressed air supply. This halves the vessel volume helping to build up the pressure more quickly.
ManufacturerAircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at
52-2500900
- Compressed air tank according to AD 2000 / without fitting set / 11 and 16 bar
- Hot dip galvanized inside and outside
- Constructed in accordance with EC Directive 87/404 / EEC or PED 97/23 / EC -AD 2000, Module: H / H 1
- Operating conditions according to AD 2000 - S1 (10/2000) = arrivals and departures and 20% pressure fluctuation range
- ISO 9001:2015 certified manufacturer
ManufacturerMaschinen- und Behälterbau GmbH
Betzdorfer Straße 170, 57567 Daaden, Germany
www.mabe.de
52-2048018
- Absorbed oils are reliably bound in hermetically sealed cartridges - no contact with contaminants
- Easy adjustment to changing compressed air and condensate requirements
- Condensate is actively pressed through the pre-filter and main filter with light blasts of compressed air
- Permanent function monitoring
- Fail-safe mode in the event of a power failure and loss of compressed air: QWIK-PURE continues to work like conventional gravity separators
QWIK-PURE series
- Absorbed oils are reliably bound in hermetically sealed cartridges - no contact with contaminants
- Simple, clean and ergonomic cartridge replacement
- Simple adjustments to changing compressed air and condensate requirements
- Sizing according to service interval or compressor capacity
From QWIK-PURE 15
- Condensate is actively pressed through the pre-filter and main filter with light blasts of compressed air
- Permanent function monitoring
- Integrated FRC control unit: reliable display of the remaining capacity of the cartridges and automatic monitoring of when condensate needs to be pushed through with light blasts of compressed air
- Integrated monitoring optimally utilizes the cartridges
- Remote monitoring possible thanks to network capability
- No overflowing of the system thanks to active operating principle with automatic drainage
- Fail-safe mode in the event of power failure and loss of compressed air: independent initiation of measures and triggering of alarms in the event of problems. For safe operation, QWIK-PURE then continues to work like conventional gravity separators.
ManufacturerBEKO Technologies GmbH
Im Taubental 7, 41468 Neuss, Germany
www.beko.de
