Sanding sponge 70 x 25 x 100 mm, P60, 58T160 by GRAPHITE is a sponge designed for hand sanding and finishing. Used for smoothing putty, drywall, plaster, paint, plastics, wood, metal and varnish coatings. The abrasive grain made of electro-corundum is located on four sides of the sponge. The soft structure allows it to conform to the shape of the surface to be sanded, and for hard-to-reach areas, the sponge can be easily cut into smaller pieces. Thanks to its thickness and flexibility, the GRAPHITE sanding sponge distributes the pressure of the hand evenly, avoiding localised depressions and scratches.
Sanding canvas in roll 2.5 m x 115 mm, P180, 58T445 by GRAPHITE is an accessory for sanding metal, wood, plastic and plasterboard. The product is made on the basis of J-type canvas, which is characterised by high flexibility and durability. The abrasive has a solid blank - 100% of the surface is covered with abrasive grain (electrocorundum), ensuring effective sanding. GRAPHITE brand canvas is designed for hand sanding.
GRAPHITE's 75mm diameter, crimped steel wire butt brush, M14, 57T428 is made from crimped steel wire. Equipped with an M14 thread, it is designed for use with angle grinders. The maximum speed of the tool is 12500 rpm. The product complies with EN 1083-2 and is well suited for roughing metal surfaces, aggressive cleaning, removing rust, paint or dirt.
P100 karedusega lihvkettad sobivad pindade vahelihvimiseks, tasandamiseks ning ettevalmistamiseks enne viimistlustöid. Takjakinnitus võimaldab kulunud lihvketta kiiret ja mugavat vahetamist, tagades tõrgeteta töö. Lihvkettad sobivad puidu, metalli ja plastiku töötlemiseks. Kuna kettad on ilma tolmuavadeta, sobivad need lihvmasinatele, mis ei vaja tolmueemaldusavadega tarvikuid. Pakendis on 5 lihvketast.
Segmented diamond cutting disc, 115 x 22.2 mm, dry and wet 57T306 by GRAPHITE is a segmented dry and wet cutting disc with a diameter of 115 mm and a mounting hole of 22.2 mm. The cutting segment is 7 mm high and 2 mm wide. The maximum speed of the disc is 13 200 rpm, corresponding to 80 m/s. The GRAPHITE blade meets the requirements of the EN13236 standard. It is designed for cutting granite, concrete, brick, stone and marble.
GRAPHITE's 6.35mm pilot drill adapter for bi-metal holesaws 32-152mm, Hex 56T754 is designed for bi-metal holesaws with diameters from 32 to 152mm. It has a 7/16" HEX shank. The pilot drill bit is made of HSS material. The adapter is used when drilling in metal, stainless steel (Inox), cast iron, brass, aluminium and wood. The set includes a screw-mounted guide drill bit. The GRAPHITE brand adapter is designed for mounting bi-metal holesaws in drills.
GRAPHITE's 14 TPI, HCS, 65 mm 57T505 plunge-cutting blade for the multifunction machine is a tool made of tough carbon steel (HCS), with a working width of 65 mm and 14 TPI. The blade is designed for plunge cutting in wood. The use of three-sided sharpened teeth and their spacing of 1.75 mm - enables fast and precise cutting. The maximum cutting depth is 40 mm and the blade thickness is 0.7 mm. The Multifunction Saw Blade from the GRAPHITE brand is the choice for efficient wood cutting in assembly and renovation work.
The 40 mm bi-metal hole saw 56T709 by GRAPHITE, with a height of 44 mm, allows drilling to a depth of 38 mm. It is made from HSS high speed steel and is fitted with a 5/8'' x 18 UNF thread. It is designed to work in metal, stainless steel (Inox), cast iron, brass, aluminium and wood. The GRAPHITE hole saw is recommended to be used with the 56T754 adapter with pilot drill bit for bi-metal holesaws in the 32-152 mm range. Maximum speeds for this tool, vary depending on the material: steel - 220 rpm, Inox steel - 110 rpm, aluminium - 330 rpm, wood - 290 rpm, cast iron - 145 rpm, brass - 290 rpm. The bi-metal hole saw is designed for use with a drill or drill/driver.
The 50 mm nylon butt brush with 6 mm shank 57T418 by GRAPHITE is made of nylon. Its maximum speed is 4,500 rpm. The product meets the requirements of EN 1083-2 and comes with a 6 mm shank, allowing it to work with any drill or screwdriver. The GRAPHITE nylon brush is a versatile product for many woodworking tasks.
The circular wire brush 125 x 20 mm, crimped wire, brassed 57T407 by GRAPHITE is made of crimped brassed wire. It has a maximum rotational speed of 6,000 rpm. The product complies with EN 1083-2 and includes reductions: 2 x 12.3 mm (1/2"), 2 x 16 mm (5/8"). The mount is suitable for use with angle grinders. The GRAPHITE wire brush is a versatile product for many tasks, including aggressive cleaning and roughing pre-machining.
Sanding canvas in roll 2.5 m x 115 mm, P100, 58T443 by GRAPHITE is an accessory for sanding metal, wood, plastics and plasterboard. The product is made on the basis of J-type canvas, which is characterised by high flexibility and durability. The abrasive has a solid blank - 100% of the surface is covered with abrasive grain (electrocorundum), ensuring effective sanding. GRAPHITE brand canvas is designed for hand sanding.
Jigsaw blade, 6 TPI, HCS, T-handle, 2 pieces, clean cut 57T548 by GRAPHITE is a jigsaw blade with 6 TPI tooth density, made of HCS and fitted with a T-handle. The set includes 2 pieces. It has an overall length of 100 mm, a working length of 74 mm, a width of 8 mm, a thickness of 1.5 mm and a tooth spacing of 4 mm. Suitable for cutting softwood, chipboard, carpenter's plywood and fibreboard 10-45 mm thick. The GRAPHITE brand blade enables clean cutting.
Velcro sanding papers, iron 102 x 152 mm, P240, 5 pieces, with 11 holes 58T308 by GRAPHITE is a set of 5 pieces of Velcro sanding papers, 102 x 152 mm. They are characterised by a cut-out in the shape of a so-called iron - with the possibility of detaching one of the pieces and fitting it to a sander with a delta foot. The accessories have a paper backing and an electro-corundum coating. They are designed for machine use. With 11 holes on the surface, they allow them to be used on sanders equipped with a dust extraction system. The Velcro attachment allows for quick and easy changing of the GRAPHITE sanding sheets. They are suitable for use on wood, metal, plastic, glass and plasterboard.
GRAPHITE's 115 mm diameter wire wheel brush, crimped steel wire, M14, 57T436 is made from crimped steel wire. Equipped with an M14 thread, it is designed for use with angle grinders. The maximum speed of the tool is 12500 rpm. The product complies with the EN 1083-2 standard and is well suited for working on metal surfaces, cleaning, removing rust, paint or dirt.
GRAPHITE's 30mm 56T734 diamond hole saw has a brazed diamond blank and a cylindrical shank. It is designed for efficient drilling in stoneware, ceramics, glass and brick. It can work either wet or dry, and the drilling itself is done without impact. The maximum speed of the hole saw is 3000 rpm, while its maximum drilling depth is 30 mm. The GRAPHITE-branded tool is designed for drilling with a drill or a screwdriver.
Sanding grid 115 x 280 mm, P150 58T155 by GRAPHITE recommended for handheld applications with wood, metal, plastic, glass and plasterboard. It features a double-sided grit and black silicon carbide grain. It is a waterproof, easy-to-clean GRAPHITE mesh that flexibly adapts to the surface. Thanks to the double-sided grit, it is economical and efficient to work with. It will prove its worth in many tasks.
Sanding sponge 70 x 25 x 100 mm, P80, 58T161 by GRAPHITE is a sponge designed for hand sanding and finishing. Used for smoothing putty, drywall, plaster, paint, plastics, wood, metal and varnish coatings. The abrasive grain made of electro-corundum is located on four sides of the sponge. The soft structure allows it to conform to the shape of the surface to be sanded, and for hard-to-reach areas, the sponge can be easily cut into smaller pieces. Thanks to its thickness and flexibility, the GRAPHITE sanding sponge distributes the pressure of the hand evenly, avoiding localised depressions and scratches.
Turbo diamond cutting wheel, 230 x 22.2 mm, dry 57T320 by GRAPHITE is a turbo dry cutting wheel with a diameter of 230 mm and a mounting hole of 22.2 mm. A practical reduction ring is included. The cutting segment is 7 mm high and 2.8 mm wide. The maximum speed of the disc is 6 600 rpm, corresponding to 80 m/s. The GRAPHITE blade meets the requirements of EN 13236 and is designed for cutting stone, brick, marble, granite and concrete.
Segmented diamond cutting wheel, 180 x 22.2 mm, dry 57T310 by GRAPHITE is a segmented dry cutting wheel with a diameter of 180 mm and a mounting hole of 22.2 mm. A practical reduction ring is included. The cutting segment is 7 mm high and 2.4 mm wide. The maximum speed of the disc is 8 600 rpm, corresponding to 80 m/s. The GRAPHITE disc meets the requirements of EN 13236 and is designed for cutting granite, concrete, brick, stone and marble.
The Wood Drill, Extended 6 x 400 mm 54T556 by GRAPHITE is a drill bit designed for working with wood and plywood and features a cylindrical chuck. It is characterised by a diameter of 6 mm and a length of 400 mm. Suitable for tasks with a maximum speed of 2500 rpm. It will work well for many DIY tasks.
