AIRCRAFT

• Wired remote control for AIRCRAFT energy saver Art. 2150001 and 2150003
• Including 5 m cable

Note: The electrical connection must be made by a licensed company or by purchasing a new energy saver by factory assembly.
Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Two-stage high-performance 2-cylinder engine with gray cast iron cylinder block
• Low speed for quiet, low-vibration operation and long life
• Large fan for optimum performance Cooling
• High-quality electric motors equipped with motor protection switch
• With phase inverter for easy manual reversal of the direction of rotation
• Intermediate and aftercooler reduce condensation
• Maintenance block with two pressure gauges for tank pressure and working pressure and high-quality CONDOR pressure switch
• Fully automatic on-off operation
• Ready for connection with all fittings
• Fifteen-year rust-proofing on inside and out external hot-dip galvanized compressed air tank

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Extremely quiet due to sound-insulated housing and additional silencer on the intake filter
• Two-cylinder high-performance unit made of grey cast iron with low speed guarantee particularly quiet and low-vibration operation -> less wear - longer service life
• Large fan impeller on the compressor and temperature-controlled radial fan on the housing ensure optimum cooling of the entire interior
• Equipped with glycerine pressure gauge, operating hours counter and error display via LED lights

• Extremely quiet due to sound-insulated housing and additional silencer on the intake filter
• Suitable for installation even in noise-sensitive areas and the direct working environment
• Two-cylinder high-performance unit made of grey cast iron with low speed warrantys particularly quiet and low-vibration operation: less wear and longer service life
• Large fan impeller on the compressor and temperature-controlled radial fan on the housing ensure optimum cooling of the entire interior
• Inter- and aftercooler as well as an additional air duct between motor and compressor reduce condensate formation
• High-quality Condor pressure switch
• Equipped with glycerine pressure gauge, hour meter and fault indication via LED lights
• Quality electric motor with motor protection switch and start-up relief
• Integrated phase monitoring
• Facility for easy tensioning of the V-belt
• Service-friendly design
• Ready for connection with all fittings and safety devices
• Models with compressed air tank: Galvanised air reservoir inside and out with 15-year warranty against rusting through

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Innovative LOGIN control with 4.3" touch screen for easy operation and complete control over all functions
• Connection of up to eight compressors possible, no matter if with constant or variable speed
• All information on current operating status at a glance
• Rotation direction control for the motor, prevents damage during start-up or after a change of location
• Low noise emission (only max. 67 dB) during operation, due to extremely low speed of the screw compressor and use of a low-noise radial fan
• Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled centrifugal fan, optimum cooling air flow and generously dimensioned heat exchangers
• Aftercooler reduces the effort for drying and filtration of the generated compressed air
• Star-delta switching as standard
• Easy to service: simple removal and installation of all components requiring maintenance

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• The two-stage compression 2-cylinder high-performance unit enables a very low speed, resulting in a particularly quiet and low-vibration run
• Large fan ensures optimal cooling
• Intercooler and aftercooler ensure a low container inlet temperature and thus reduce condensation
• High quality electric motor with high torque
• Electric motor equipped with motor protection switch
• Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
• Flexible armored hose line with heat protection prevents vibration breakage
• High-quality CONDOR pressure switch as standard
• From 7.5 kW as standard with star-delta switch with operating hours counter
• Ready for connection with all fittings

Additional equipment K-version:

• Refrigerated dryer with integrated automatic steam trap for dry compressed air, longer service life of compressed air tools and avoidance of disturbances in pneumatic controls
• Fine filter for separating condensate and solid impurities with particles up to 1 μ in front of the refrigeration dryer

Equipment

• Automatic steam trap on the compressed air tank
• No unnecessary pressure loss


• Condensate conditioner for oil-water separation
• Important notes on condensate treatment can also be found in the section on compressed air preparation.


• Fine filter for separating condensate and solid impurities with particles up to 1 μm
• Compressed air quality according to ISO 8573-1
• As a pre-filter in front of the refrigeration dryer


• Refrigerated dryer with integrated automatic steam trap
• Pressure dew point at 5 °C, ambient temperature 25 °C, atmospheric dew point at -22 °C

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Cylinders and cylinder heads with long ribs for optimum heat dissipation;
• carefully balanced crankshaft made of cast iron for better concentricity
• Stainless steel valves with high air flow
• Pulley designed as a fan
• Optimized airflow, high fan performance
• Highly efficient air filter with labyrinth intake channel for noise reduction

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Sintered filter with centrifugal principle
• For compressed air and neutral gases
• Inlet pressure 1.5 - 16 bar
• Suitable for temperatures from -10 to +50°C
• Semi-automatic condensate drain
• For vertical installation

• Sintered filter with centrifugal principle
• For compressed air and neutral gases
• Inlet pressure 1.5 - 16 bar
• Suitable for temperatures from -10 to +50°C
• Semi-automatic condensate drain
• For vertical installation

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Ideal in combination with prefabricated solutions
• Permanently sealed without pressing
• Installation even in confined spaces
• Detachable fittings can be reused
• Cost savings through quick assembly

• Permanently sealed without pressing
• Cost savings through quick and easy assembly
• Ideal in combination with prefabricated solutions
• Compatible with other standards-compliant pipes
• No confusion of contours possible
• Installation even in confined spaces
• Extraction forces far beyond the requirements of the standard
• Pipe components can be dismantled and reused
• Numerous national and international approvals
• O-rings included

Manufacturer
Aalberts integrated piping systems B.V.
Oude Amersfoortseweg 99, 1212 NL Hilversum, Netherlands
www.aalberts-ips.com

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Innovative LOGIN control with 4.3" touch screen for easy operation and full control of all functions.
• Rotation direction control for the motor, prevents damage during start-up or after a change of location
• High cooling effect and low noise level due to thermostatically controlled radial fan
• Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled centrifugal fan, optimum cooling air flow and generously dimensioned heat exchangers
• Aftercooler reduces the effort for drying and filtration of the generated compressed air
• Easy to service: simple removal and installation of all components requiring maintenance

Latest generation IE4 permanent magnet motor for max. energy efficiency

• Larger speed/load range
• Larger delivery volume supply range
• Extremely energy efficient - up to 50% energy consumption savings compared to a "fixed speed" model
• Very quiet operation - only 64 dB

Energy saving through frequency control

• Ideal for frequently changing compressed air consumption
• Compressor delivery rate adjusts to actual consumption
• Electronic control monitors motor and compressor speed and keeps line pressure constant even when consumption fluctuates widely
• Advanced and efficient cutting-edge technology in the smallest possible space

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

Advantages of DRYPOINT eco control

• Integrated DRYPOINT M Plus solution: filtration and dryer in a compact form, as well as condensate drain integrated
• Filtration on the spot in the treatment chain where the highest efficiency is achieved
• Easy maintenance / replacement of filter element as with a filter
• Application-specific degree of dryness can be selected
• Consistent compressed air quality under fluctuating operating conditions
• Energy saving through minimization of purging air consumption for actual amount of useful air and degree of drying
• Power evaluation via LED, forwarding via current output 4 … 20 mA possible
• User-friendly: Easy to use, test functions, error messages
• Concept based on the fail-safe principle, error message can be picked up via potential-free contact

Functionality of the DRYPOINT® M eco control

Based on the measurement result from the sensor, the control software decides in defined cycles whether and how long the full amount of purge air has to be provided to achieve and stabilize the required degree of dryness. This process is implemented by means of a targeted clocking of a solenoid valve. In each cycle, the duration of the two process sections described below varies in order to keep the degree of drying within the specified tolerance range.

Manufacturer
BEKO Technologies GmbH
Im Taubental 7, 41468 Neuss, Germany
www.beko.de

EV WS / EA hood incl. relief valve
F4x1/4" connection
preset to 7.8 to 9.8bar
adjustable up to max. 16bar
at 400V max. 16Ampere
at 500V max. 9Ampere
Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
• With star-delta switch
• High cooling effect and lower noise level due to thermostatically controlled radial fan
• Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirement via automatic message
• Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
• Screw compressor with wear-resistant Poly V ribbed belt drive and slide clamping system
• Easy maintenance due to easily accessible elements
• Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
• Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
• Small external dimensions, thus easy transport and installation
• Fifteen-year warranty against rusting through on the inside and outside of hot-dip galvanized compressed air tanks

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Compressed air tank according to AD 2000 / without fitting set / 11 and 16 bar
• Hot dip galvanized inside and outside
• Constructed in accordance with EC Directive 87/404 / EEC or PED 97/23 / EC -AD 2000, Module: H / H 1
• Operating conditions according to AD 2000 - S1 (10/2000) = arrivals and departures and 20% pressure fluctuation range
• ISO 9001:2015 certified manufacturer

Manufacturer
Maschinen- und Behälterbau GmbH
Betzdorfer Straße 170, 57567 Daaden, Germany
www.mabe.de

• Suitable for compressed air with full free passage
• Temperature resistant from -20 ° C to + 180 ° C

Manufacturer
Bongas Deutschland GmbH
Raiffeisenstraße 13, 77704 Oberkirch, Germany
www.bongas.de

• Sintered filter with centrifugal principle
• For compressed air and neutral gases
• Inlet pressure 1.5 - 16 bar
• Suitable for temperatures from -10 to +50°C
• Semi-automatic condensate drain
• For vertical installation

• Sintered filter with centrifugal principle
• For compressed air and neutral gases
• Inlet pressure 1.5 - 16 bar
• Suitable for temperatures from -10 to +50°C
• Semi-automatic condensate drain
• For vertical installation

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

Special

• Drying by partial vapor pressure compensation of water vapor by diffusion in combination with a highly selective membrane
• No change in the compressed air composition - can be used for breathing air treatment

Efficient

• Reaches the required pressure dew point with low energy consumption
• Very fast availability of dried compressed air
• Filtration and drying compact in one device

Robust

• Housing made of seawater-resistant aluminum
• Low-maintenance, currentless technology

System-compatible

• Modularly combinable with CLEARPOINT Filter program
• Can be used anywhere along the compressed air treatment chain - can also be integrated into system technology

• The ultimate membrane dryer technology with integrated nanofilter
• Filtration and drying in one housing (simple filter element change)
• Low purge air requirement (Twist 60 technology)
• Availability of dried compressed air immediately without running-in phase
• Safe drying due to the high partial vapor pressure gradient
• No change in the compressed air temperature and composition
• Proven 100,000 times
• Maintenance-free (except filter element change)
• For diverse applications, including for breathing air treatment
• Also ideal for use directly behind the compressor / aftercooler
• Optionally also for higher loads (assembly potting, 16 bar, 70°C)
• For a reliable function of the DRYPOINT M membrane dryer must meet the following requirements:
1. The incoming compressed air must not contain any liquid condensate
2. Particles larger than 1 μm must be separated before the membrane dryer
3. The oil content of the compressed air must not exceed 0.01 mg/m³.

• DRYPOINT M membrane dryers have been an alternative to existing ones for years Compressed air drying process proven.

Advantages DRYPOINT M PLUS

• Proven process of highest reliability and functional safety
• Immediate availability of dry compressed air, even when working discontinuously
• Low purge air requirement, compressed air drying can be adjusted to the application
• Compact and robust, small space requirement due to low overall height
• Compressed air inlet and outlet on one level (filter version), easy to combine with CLEARPOINT filters
• Maintenance and wear-free as there are no moving parts
• No reduction in the oxygen content, therefore also suitable for breathing air treatment
• No electrical connection, also suitable for Ex areas
• Long service life in case of use of CLEARPOINT filters
• Environmentally friendly, does not require CFCs / CFC-containing refrigerants or adsorbents
• Complete solution: filtration and dryer in a compact form, integration of drain pipe
• Filtration at the point in the treatment chain where the highest efficiency is achieved
• Easy maintenance / replacement of filter element as with a regular filter

Filter element: N (nanofilter)

• The CLEARPOINT filter element type N is used to separate solid particles down to 0.01 micron, water and oil aerosols . The element has a multi-stage structure for efficient and long-lasting filtering. In the first stage, coarse particles are retained by a pre-filter layer. In the second stage, finer particles are absorbed by a depth filter bed made of high-performance borosilicate fiber fabric. Due to the very large cavity volume of the filter medium (96%), a very high dirt holding capacity is achieved. The filter medium is specially impregnated in order to avoid cross-sectional swelling of the individual fibers.

Trap: Float trap

• The basic version includes a float drain.

Size 10 - 40

• This size is for the demand-oriented compressed air drying of medium volume flows configured. Different levels of drying of the compressed air are achieved through different purge air settings.

Manufacturer
BEKO Technologies GmbH
Im Taubental 7, 41468 Neuss, Germany
www.beko.de

• Innovative LOGIN control with 4.3" touch screen for easy operation and complete control over all functions
• Connection of up to eight compressors possible, no matter if with constant or variable speed
• All information on current operating status at a glance
• Rotation direction control for the motor, prevents damage during start-up or after a change of location
• Low noise emission (only max. 67 dB) during operation, due to extremely low speed of the screw compressor and use of a low-noise radial fan
• Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled centrifugal fan, optimum cooling air flow and generously dimensioned heat exchangers
• Aftercooler reduces the effort for drying and filtration of the generated compressed air
• Service-friendly: easy removal and installation of all components requiring maintenance

Energy saving through frequency control

• Ideal for frequently changing compressed air consumption
• Compressor delivery rate adjusts to actual consumption
• Electronic control monitors motor and compressor speed and keeps line pressure constant even when consumption fluctuates widely

Manufacturer
Aircraft Kompressorenbau und Maschinenhandel GmbH
Gewerbestraße Ost 6, 4921 Hohenzell, Austria
info@aircraft.at

• Cylinders and cylinder heads with long ribs for optimum heat dissipation;
• carefully balanced crankshaft made of cast iron for better concentricity
• Stainless steel valves with high air flow
• Pulley designed as a fan
• Optimized airflow, high fan performance
• Highly efficient air filter with labyrinth intake channel for noise reduction

Manufacturer
FNA S.p.A.
Via Einaudi 6, 10070 Robassomero, Italy
info@fnacompressors.com