Laastuimurid

• Universally applicable also for plastic, metal, glass, styrofoam, paper and the like
• Particularly robust construction
• Housing made of galvanized sheet steel
• Paddle wheel fan for increased suction power
• Significantly reduced dust content due to double-woven fine filter bag
• Extractors comply with dust class L
• Basic units are pre-assembled in modular design
• For large systems only short installation times
• Top value for money
• Short assembly times thanks to modular design

• Dust tested to H3, residual dust content less than 0.1 mg / m³
• Suitable for vacuuming and separating dry wood and plastic chips
• High extraction capacity with a small footprint
• Maximum performance in this class
• Very quiet
• All models with a collision protection

• Designed for commercial use
• For all woodworking machines with corresponding extraction nozzle diameter

• Robust and compact housing made of galvanized sheet steel
• Extraction nozzle easily convertible from left to right, thus flexible use
• Large inspection openings
• Large-sized, mobile chip container with clamp and chip collecting bag
• Dust remover at delivery already completely assembled, thus quick to use
• All models mobile
• For model RLA 210: Optimum chip distribution in the chip containers due to large filter surface
• Maximum safety, thanks to antistatic filter elements

• Ultra compact with maximum filter surface
• Filter material made of polyester fleece, aluminised, therefore with long service life
• Standard anti-static filter tested and approved according to M-BIA category
• The fan is connected downstream of the filter

• Universally applicable also for plastic, metal, glass, styrofoam, paper and the like
• Particularly robust construction
• Housing made of galvanized sheet steel
• Chip drums are powder coated
• Paddle wheel fan for increased suction power
• Significantly reduced dust content due to double-woven fine filter bag
• Extractors comply with dust class L
• Basic units are pre-assembled in modular design
• For large systems only short installation times
• Top value for money
• Short assembly times thanks to modular design

• Universally applicable also for plastic, metal, glass, styrofoam, paper and the like
• Particularly robust construction
• Housing made of galvanized sheet steel
• Paddle wheel fan for increased suction power
• Significantly reduced dust content due to double-woven fine filter bag
• Extractors comply with dust class L
• Basic units are pre-assembled in modular design
• For large systems only short installation times
• Top value for money
• Short assembly times thanks to modular design

• Dust tested to H3, residual dust content less than 0.1 mg / m³
• Suitable for vacuuming and separating dry wood and plastic chips
• High extraction capacity with a small footprint
• Maximum performance in this class
• Very quiet
• All models with a collision protection

• Designed for commercial use
• For all woodworking machines with corresponding extraction nozzle diameter

• Robust and compact housing made of galvanized sheet steel
• Extraction nozzle easily convertible from left to right, thus flexible use
• Large inspection openings
• Large-sized, mobile chip container with clamp and chip collecting bag
• Dust remover at delivery already completely assembled, thus quick to use
• All models mobile
• For model RLA 210: Optimum chip distribution in the chip containers due to large filter surface

• Ultra compact with maximum filter surface
• Filter material made of polyester fleece, aluminised, therefore with long service life
• Standard anti-static filter tested and approved according to M-BIA category
• The fan is connected downstream of the filter
• Maximum safety, thanks to antistatic filter elements

• Max detaili Ø 305 mm
• Tsentri kõrgus 155 mm
• Tsentrite vahe 460 mm
• Spindli keere M33 x 3,5
• Kiirused 650-1430, 1240-2790, 1600-3800 min-1
• Kiiruse reguleerimine elektrooniline
• Pinge 230 V / 50 Hz
• Mootori võimsus 550 W
• Tagapuki koonus MT 2
• Mõõtmed (P x L x K) 900 x 340 x 410 mm
• Kaal 38 kg

• For milling, planing and sawdust
• High-quality, stable chassis for easy manoeuvring
• Fine filter bag double woven

• For milling, planing and sawdust (not suitable for dust)
• 180° rotatable suction unit enables suction routing from below or above
• Stable fan wheel made of metal
• Standard with high-quality chassis for better stability and easy manoeuvring
• Quick-release fasteners for filter and chip sack
• Fine filter bag double woven

• Clean exhaust air due to separation of dust in the cyclone separator and cartridge filter
• Automatic filter cleaning for consistently high extraction performance
• Includes remote control and timer function to turn on
• Easy to empty the mobile container
• ./li>
• Including remote control and timer function for switching the extraction on and off
• Easy emptying of the mobile container

• Effective cyclone technology with 2-stage filtration
• Separation of larger impurities in the waste container and fine dust in the cartridge filter
• Sight glass for checking the fill level in the container
• Automatic filter cleaning for consistently high extraction performance
• Timer and on/off function possible via remote control
• Flexible maneuvering thanks to castors on the extraction unit and filling container
• Easy emptying of the mobile filling container thanks to quick-release fastener
• Suitable for multiple machines thanks to adapter for three suction nozzles
• Extremely quiet

• Tootlikus 1900 m³/h
• Maks. hõrendus 1700 Pa
• Filtri pindala 1.92m²
• Laastukoti maht 110 l
• Sisendava 203mm/1x100mm + 1x120mm
• Mootor 1,5kW/400V
• Üldmõõdud 1000x500x2100
• Kaal 39kg

• Dust tested to H3, residual dust content less than 0.1 mg / m³
• Suitable for vacuuming and separating dry wood and plastic chips
• High extraction capacity with a small footprint
• Maximum performance in this class
• Very quiet
• All models with a collision protection

• Designed for commercial use
• For all woodworking machines with corresponding extraction nozzle diameter

• Robust and compact housing made of galvanized sheet steel
• Extraction nozzle easily convertible from left to right, thus flexible use
• Large inspection openings
• Large-sized, mobile chip container with clamp and chip collecting bag
• Dust remover at delivery already completely assembled, thus quick to use
• All models mobile
• For model RLA 210: Optimum chip distribution in the chip containers due to large filter surface

• Ultra compact with maximum filter surface
• Filter material made of polyester fleece, aluminised, therefore with long service life
• Standard anti-static filter tested and approved according to M-BIA category
• The fan is connected downstream of the filter
• Maximum safety, thanks to antistatic filter elements

• For use in workshops with a simultaneity factor of 1-2 machines, from RLA 2501 2-3 machines (depending on the required volume flow) or as a decentralized extraction unit to supplement an existing stationary system
• For universal use with a wide range of materials - also suitable for dry aluminum chips!
• 100% air recirculation without additional costs and construction work
• Delivery ready for connection
• High suction capacity
• Low costs for pipe components and installation, especially when replacing old and no longer approved systems
• Integrated pre-separation chamber to reduce the load and protect the filters
• Compact dimensions, allowing the units to be installed in previously unused areas
• Intake side can be ordered with orientation to the left or right, enabling the use of workshop niches
• Control system can be expanded using plug-in technology

From model RLA 2501 P:

• Optimum filter cleaning during operation (RLA 1601P-2001P) and at standstill after a minimum running time has been added up

• For use in workshops with a simultaneity factor of 1-2 machines, from RLA 2501 2-3 machines (depending on the required volume flow) or as a decentralized extraction unit to supplement an existing stationary system
• For universal use with a wide range of materials - also suitable for dry aluminum chips!
• 100% air recirculation without additional costs and construction work
• Delivery ready for connection
• High suction capacity
• Low costs for pipe components and installation, especially when replacing old and no longer approved systems
• Integrated pre-separation chamber to reduce the load and protect the filters
• Compact dimensions, allowing the units to be installed in previously unused areas
• Intake side can be ordered with orientation to the left or right, enabling the use of workshop niches
• Control system can be expanded using plug-in technology

From model RLA 2501 P:

• Optimum filter cleaning during operation (RLA 1601P-2001P) and at standstill after a minimum running time has been added up

• High-performance bag filter with special surface coating
• Filter of category M
• Dust tested to H3, residual dust content < 0.1 mg / m³
• Large dimensioned filling container for easy and quick replacement of chip bags extendable
• Level controlled by a sight glass
• Approved as industrial vacuum cleaner in conjunction with a floor cleaning set
• Reduced power consumption at full suction power and economical consumption thanks to optimized air flow and high-performance fan with backward-curved impeller arranged on the clean air side
• With aerodynamically sophisticated housing
• Optimum pre-separation by a cyclone already in the intake area
• Filters with large folds, therefore easy to clean, so that highest filter life is achieved and only very low maintenance and operating costs
• Filter cleaning via a hand lever
• M version with automatic filter cleaning
• Due to its low weight, swivel castors and large handles, it can be used quickly and efficiently at various workstations

• Universally applicable also for plastic, metal, glass, styrofoam, paper and the like
• Particularly robust construction
• Housing made of galvanized sheet steel
• Paddle wheel fan for increased suction power
• Significantly reduced dust content due to double-woven fine filter bag
• Extractors comply with dust class L
• Basic units are pre-assembled in modular design
• For large systems only short installation times
• Top value for money
• Short assembly times thanks to modular design

• For milling, planing and sawdust
• High-quality, stable chassis for easy manoeuvring

• For milling, planing and sawdust (not suitable for dust)
• 180° rotatable suction unit enables suction routing from below or above
• Stable fan wheel made of metal
• Standard with high-quality chassis for better stability and easy manoeuvring
• Quick-release fasteners for filter and chip sack

• Solid cast iron bench bed for extremely smooth running
• ASR run-off protection groove for maximum safety when fastening clamping devices
• Manual speed adjustment via 5-stage belt drive
• Easy switching between clockwise and counter-clockwise rotation

• Solid cast iron bench bed for extremely smooth running
• ASR run-off protection groove for maximum safety when fastening clamping devices
• Manual speed adjustment via 5-stage belt drive
• Easy switching between clockwise and counter-clockwise rotation
• Can also be used as a stand-alone machine thanks to optional base frame

• Electrically movable bench bed extension via cylinder to a center width of up to 1016 mm
• Extremely high center height of up to 397 mm, workpieces of up to 790 mm diameter possible
• ASR run-off protection groove for maximum safety when fastening clamping devices
• Comfortable working thanks to infinitely variable speed adjustment via frequency converter
• Practical 36-step spindle part adjustment for precise positioning of e.g. drill holes or milled holes

• Solid gray cast iron bench bed for smooth running
• Electrically movable bench bed extension via cylinder to a center width of up to 1016 mm
• Extremely high center height of up to 397 mm, workpieces of up to 794 mm diameter possible
• ASR run-off protection groove for maximum safety when fastening clamping devices
• Comfortable working thanks to infinitely variable speed adjustment via frequency inverter
• Frequency inverter for better power development at low speeds
• Robust tailstock with trapezoidal thread and 120 mm quill travel
• Flexible working thanks to mobile control box with magnetic holder, can be positioned as required
• Digital speed display and right/left rotation changeover via the control box
• Practical 36-step spindle indexing device for precise positioning of e.g. drill holes or milling operations

• Universally applicable also for plastic, metal, glass, styrofoam, paper and the like
• Particularly robust construction
• Housing made of galvanized sheet steel
• Paddle wheel fan for increased suction power
• Significantly reduced dust content due to double-woven fine filter bag
• Extractors comply with dust class L
• Basic units are pre-assembled in modular design
• For large systems only short installation times
• Top value for money
• Short assembly times thanks to modular design

• Dust tested to H3, residual dust content less than 0.1 mg / m³
• Suitable for vacuuming and separating dry wood and plastic chips
• High extraction capacity with a small footprint
• Maximum performance in this class
• Very quiet
• All models with a collision protection

• Designed for commercial use
• For all woodworking machines with corresponding extraction nozzle diameter

• Robust and compact housing made of galvanized sheet steel
• Extraction nozzle easily convertible from left to right, thus flexible use
• Large inspection openings
• Large-sized, mobile chip container with clamp and chip collecting bag
• Dust remover at delivery already completely assembled, thus quick to use
• All models mobile
• For model RLA 210: Optimum chip distribution in the chip containers due to large filter surface

• Ultra compact with maximum filter surface
• Filter material made of polyester fleece, aluminised, therefore with long service life
• Standard anti-static filter tested and approved according to M-BIA category
<
• The fan is connected downstream of the filter
• Maximum safety, thanks to antistatic filter elements

• For milling, planing and sawdust (no dust)
• Significantly reduced dust content by BIA-tested filter material with a high degree of separation
• Housing parts and impellers made of high-strength special plastic
• Quick-release fasteners for filters and chip bags for trouble-free maintenance
• Robust, high-quality execution
• Easy to move through castors
• Low energy consumption
• Extractors comply with dust class L

• Fine dust filter cartridge with specially treated polyester fleece
• Retains finest particles
• High airflow, large filter surface
• Higher tear resistance and therefore longer service life