UUTUUDET

• The electronic measuring components of the measuring strips are protected and sealed in the housing
• Allows accurate and reliable measuring results even if the measuring system is installed in Öl or cooling liquids
• Tolerant against vibrations and magnetic interference
• Without mounting

• The electronic measuring components of the measuring strips are protected and sealed in the housing
• Allows accurate and reliable measuring results even if the measuring system is installed in Öl or cooling liquids
• Tolerant against vibrations and magnetic interference
• Without mounting

• Precise processing
• Powerful, maintenance-free engine
• Heavily ribbed prism bed made of gray cast iron, inductively hardened and precision ground
• Smooth-running feed gear with rounded gears running in an oil bath
• Hardened and ground Z-axis guideway
• Guaranteed concentricity of the spindle nose better than 0.009 mm
• Concentricity on the lathe chuck better than 0.04 mm
• Automatic longitudinal / lead screw drive
• Lead screw for thread cutting or automatic longitudinal turning
• Quadruple tool holder
• All guides can be adjusted by wedge strips
• Right / left rotation in the control panel switchable
• Hardened main spindle mounted in adjustable precision tapered roller bearings
• Tapered roller bearings in P5 quality
• Hardened spindle nose with Ø 26 mm spindle bore
• Rolled trapezoid spindles
• Chip protection on the upper slide
• Upper slide on cross slide slidable
• Tailstock for taper turning ± 5 mm adjustable
• Tailstock quill and handwheel with adjustable fine scale 0.02 mm
• Fast, easy and tool-free adjustment by means of a clamping lever
• Leadscrew stored in two sintered bearings
• Change gear set in standard scope of supply for thread cutting
• Handwheels on the carriage with adjustable fine scale 0.04 / 0.01 mm
• thrust bearing
• 3-jaw lathe chuck in the standard scope of delivery
• Emergency stop impact switch
• Fully equipped, allowing the user to be productive immediately after commissioning

TU 2807V

• Quiet, powerful and brushless DC drive with excellent control characteristics
• High precision steel lining for higher speeds
• Speed change easily adjustable via potentiometer
• Digital speed display

• The electronic measuring components of the measuring strips are protected and sealed in the housing
• Allows accurate and reliable measuring results even if the measuring system is installed in Öl or cooling liquids
• Tolerant against vibrations and magnetic interference
• Without mounting

• Solid design made from high-quality Meehanite cast iron
• High concentricity due to tapered roller bearing, ≤ 0.01 mm measured in the sleeve
• X- and Z-axis with adjustable 55° dovetail guide
• Y-axis with adjustable flat guide
• Coolant device
• Solid and generously dimensioned cross table, precisely surface-finished with adjustable end stops
• Drilling/milling head can be tilted ± 45
• Automatic quill feed, 3-stage 0.04 - 0.15 mm/rev
• Precision micro feed
• Adjustable drilling depth stop with millimeter scale, readable from the front
• Right/left rotation
• Infinitely variable speed control
• Milling spindle with precision bearing
• Mechanical spindle brake
• Height-adjustable protective screen with microswitch, against flying chips and parts, for maximum protection of the user

• Precisely manufactured
• Hardened and ground Z-axis guideway
• Guaranteed concentricity of the spindle nose better than 0.009 mm
• Rolled trapezoid spindles
• Leadscrew stored in two sintered bearings
• Two tapered roller bearings in P5 quality
• Precisely crafted sled
• Handwheels with adjustable fine scale 0.04 / 0.01 mm
• Quadruple tool holder
• All guides can be adjusted by wedge strips
• Concentricity - chuck better than 0.05 mm
• Lead screw for thread cutting or automatic longitudinal turning
• Right / left rotation in the control panel switchable
• Tailstock for taper turning ± 5 mm adjustable
• Tailstock quill and handwheel with adjustable fine scale 0.02 mm
• Fast, easy and tool-free adjustment by means of a clamping lever
• Emergency stop impact switch
• thrust bearing
• Extensive accessories
• 3-jaw lathe chuck in the standard scope of delivery
• Stable value

TU 2406V

• Speed change easily adjustable via potentiometer
• Digital speed display
• EMC filter class C1

• Vibration-absorbing cast design
• Oil bath gearbox with ground, hardened gear wheels
• Coolant device
• LED lamp
• Solid and generously dimensioned cross table, precisely surface-machined with T-slots and adjustable gibs
• Adjustable guide rails
• Adjustable limit stop of the X-axis
• Mechanical quill adjustment for drilling via quill lever
• Right/left rotation
• Clutch for switching from manual coarse feed to manual fine feed
• User-friendly control panel
• Height-adjustable protective screen with microswitch, against flying chips and parts, for maximum user protection

• Hardened and ground Z-axis guideway
• Motor protection switch
• Control cabinet with 24 V DC power supply
• Partial enclosure with included, large dimensioned chip guard
• Chip guard with integrated position indicator, coolant hose and additional control panel
• Two-channel safety electronics
• Safety handwheels with disengaging function in the X- and Z-axis
• Face and top slide spindle is hardened and ground and adjustable via split spindle nut
• Lead and traction spindle cover
• Finely graduated feed and tapping range
• Energy chain for gentle guiding of cables and hoses
• Standard gears for metric thread pitches and modular threads are mounted in the machine. Change gears for inch and D.P threads optionally available
• Switches with life cycle calculation tested according to EN ISO 13849
• Decoupled handwheels tested according to EN 23125
• Reduction of main spindle deceleration time by energy regeneration
• Chip tray can be pulled out to the front
• Coolant device
• Quick-change steel holder SWH 5-B
• Steel holder 25 x 120 type D for square chisel 20 mm
• LED machine lamp for complete illumination of the working area
• Cutting constant VSC

• Hardened and ground Z-axis Guideway
• Spindle mounting Camlock DIN ISO 702-2 No. 4
• Guaranteed concentricity of the spindle nose better than 0,015 mm
• Smooth-running feed gear with rounded gearwheels running in oil bath
• Emergency-stop pushbutton
• Hardened main spindle mounted in adjustable precision taper roller bearings
• Hand wheels on slide with adjustable fine scaling 0,04 / 0.01 mm
• Heavy ribbed prismatic bed made of grey cast iron, inductively hardened and precision ground
• Circular runout accuracy on lathe chuck better than 0,04 mm
• Quadruple steel holder
• All guides can be readjusted by V-guides
• Hardened spindle nose
• Lead spindle for thread cutting or automatic longitudinal turning
• Lead spindle and feed spindle mounted in two sintered bearings
• Automatic longitudinal / facing feeds
• Riding stock for taper turning ± 5 mm adjustable
• Riding stock sleeve and handwheel with adjustable fine scaling 0,02 mm
• Fast, easy and tool-free adjustment of the tailstock by means of clamping lever

• The electronic measuring components of the measuring strips are protected and sealed in the housing
• Allows accurate and reliable measuring results even if the measuring system is installed in Öl or cooling liquids
• Tolerant against vibrations and magnetic interference
• Without mounting

• Dimensions L x W x H: 630 x 400 x 100 mm
• Acceptance 7 μ
• granite
• Thermally and dynamically stable
• Compressive strength 250 - 260 N / mm2
• DIN 876/0
• corrosion-free

• The electronic measuring components of the measuring strips are protected and sealed in the housing
• Allows accurate and reliable measuring results even if the measuring system is installed in Öl or cooling liquids
• Tolerant against vibrations and magnetic interference
• Without mounting

• The electronic measuring components of the measuring strips are protected and sealed in the housing
• Allows accurate and reliable measuring results even if the measuring system is installed in Öl or cooling liquids
• Tolerant against vibrations and magnetic interference
• Without mounting

• Hardened and ground Z-axis guideway
• Precisely machined carriage
• DC 24 volt electrics
• Motor protection switch
• Main motor electrically braked
• Guaranteed concentricity of the spindle nose better than 0.015 mm
• Smooth-running feed gear with rounded gears running in an oil bath
• Hardened main spindle mounted in adjustable, precise tapered roller bearings
• Right/left rotation switchable on the bed slide
• Two-channel safety electronics
• Handwheels with adjustable fine scaling 0.04 / 0.02 mm
• Safety handwheels with disengagement function according to EN23125 in the X and Z axis
• Switch rod on the bed slide for selecting longitudinal or face feed
• Switch with life cycle calculation tested in accordance with EN ISO 13849
• Machine base in sturdy steel construction
• Quadruple steel holder
• Emergency stop switch right and left

Omadused:

• Veekindel läbiviigutugevdus toruühenduste tihendamiseks
• Sobib torudele läbimõõduga 10–24 mm
• Elastne kummimansett tagab tiheda ühenduse
• Kasutamiseks koos hüdroisolatsioonimastiksiga
• Sobib sise- ja välistingimustesse
• Täielikult veekindel ja püsivalt elastne
• Sobib niisketesse ja märgadesse ruumidesse enne plaatimist ning viimistlustöid