Two-stage compression 2-cylinder high-performance unit with cast iron cylinder block
The low speed ensures quiet, low-vibration operation and a long service life
Large fan wheel for optimal cooling
High quality electric motor with high torque
Electric motor equipped with motor protection switch
With phase inverter for easy manual reversal of the direction of rotation
Intermediate and aftercooler reduces the formation of condensation
Maintenance block with two pressure gauges for tank pressure and working pressure and high quality CONDOR pressure switch
Fifteen-year rust-through warranty on inside and outside hot-dip galvanized compressed air tank
Fully automatic on-off operation
Ready for connection with all fittings
Increased flexibility
By connecting the second compressed air tank, the container volume is doubled, whereby a higher air supply can be established
An increased demand for air can thus be covered in the short term.
The second compressed air tank can be disconnected from the compressed air supply e.g. for chiselling or sandblasting. This halves the container volume and pressure builds up faster.
Equipment details:
K version with refrigeration dryer with integrated automatic steam trap as standard
Pressure dew point 5 °C, compressed air inlet temperature 35 °C, cooling air temperature 25 °C
K version additionally with pre-filter for separating condensate and solid impurities with particles up to 1 μm
Compressed air quality according to ISO 8573-1
As a pre-filter in front of the refrigeration dryer
KK version with automatic steam trap on the compressed air tank
This condensate drainage without unnecessary pressure loss
Condensate conditioner for oil-water separation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Recommended when operating the screw compressor with start-stop operation via pressure switch without a vessel
Function Description: When the pre-set pressure is reached, the air, which continues to be pumped, is blown off pressure-free. The valve also has the function of a check valve. This means that the air behind the valve is not blown off, but only the air, which is further promoted. Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Compressed air filters are used for highly efficient removal of solid particles, water, oil, aerosols, hydrocarbons, odors and vapors from compressed air systems.
To achieve the required quality of compressed air, filters that gradually remove all types of solid and liquid contaminants from the compressed air must be installed in the compressed air line
Your advantages through better quality compressed air:
Safe filtration of both liquids such as water and aerosols as well as particles, dust and gases
Better working and production conditions
Optimum protection of connected tools and machines
Improved product quality through reduction of rejects
Protection of the compressed air system against contamination
Increase of productivity by reduction of instant maintenance
for separating solid contaminants up to 0.01μm
Residual oil aerosol content up to 0.01 mg / m³ at 20 ° C and 1 bar
Operating temperature 1.5 to 65 ° C
absolute compressed air quality according to ISO 8573-1
for safe separation of condensate and particles
complete with filter element and float valve
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
With star-delta switch
High cooling effect and lower noise level due to thermostatically controlled radial fan
Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirements via automatic message
Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
Screw compressor with wear-resistant Poly V ribbed belt drive and slide clamping system
Easy maintenance due to easily accessible elements
Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
Small external dimensions, thus easy transport and installation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
The two-stage compression 2-cylinder high-performance unit achieves a very low rotational speed, resulting in a particularly quiet and low-vibration run
This ensures a longer life due to less wear
Large fan wheel and a cooling air baffle on the cylinder for optimum cooling of the compressor
Aftercooler with cooling fins and intercooler to the aftercooler ensure a low container inlet temperature and thus less moisture in the compressed air
High quality electric motor with high torque
Electric motor equipped with motor protection switch
With high-quality CONDOR pressure switch
Equipped with a pressure gauge for tank pressure and a ball valve on the compressed air tank
Compressed air tank equipped with safety valve, container pressure gauge and condensate drain tap
Ten-year rust-through warranty on powder-coated compressed air tank
With all safety devices
Fully wired
Stable belt guard made of metal
Including swinging elements
Connection to grid by qualified electrician
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
EasyTRONIC MICRO II electronic control with pressure sensor operation as standard, thus preventing motor overload, reducing wear and extending service life
With star-delta switch
High cooling effect and lower noise level due to thermostatically controlled radial fan
Operating hours counter records load and overrun times, thus ensuring compliance with maintenance intervals - Indication of maintenance requirements via automatic message
Rotation direction control for the motor avoids possible damage during commissioning or after a change of location
Screw compressor with wear-resistant Poly V ribbed belt drive and slide clamping system
Easy maintenance due to easily accessible elements
Optimum operating temperatures due to thermostatically controlled fan, optimum cooling air flow and generously dimensioned heat exchanger, thus longer service life, lower fluctuations in oil temperature than with thermostat control
Aftercooler as standard, thus less effort for drying and filtration of the generated compressed air
Small external dimensions, thus easy transport and installation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Innovative LOGIN control with 4.3" touch screen for easy operation and full control of all functions.
Energy-efficient IE4 motor
Rotation direction control for the motor, prevents damage during start-up or after a change of stand location
High cooling effect and low noise level due to thermostatically controlled radial fan
Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled radial fan, optimum cooling air flow and generously dimensioned heat exchangers
Aftercooler reduces the effort for drying and filtration of the generated compressed air
Star-delta switching as standard
Easy to service: simple removal and installation of all components requiring maintenance
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Absolutely Low maintenance drive with maximum energy efficiency thanks to directly coupled coaxial screw compressor
EasyTronic IV control as standard prevents motor overload, reduces wear and ensures a longer service life
High cooling effect and Lower noise level thanks to the thermostatically controlled radial fan
Longer service life of the device and less fluctuations in the oil temperature thanks to the thermostatically controlled fan, optimal cooling air flow and generously sized heat exchanger
Less effort for drying and filtering the generated compressed air Integrated aftercooler
Guaranteed compliance with the maintenance intervals by recording the load and run-on times via the operating hours counter
Display of the maintenance requirement via automatic notification
Avoiding damage during commissioning or after changing location through integrated direction of rotation control for the motor
Service-friendly due to optimal accessibility and simple assembly / disassembly of all components to be serviced
Easy transport and assembly due to small external dimensions
Monitoring as standard the engine and compressor speed through SpeedTronic Control control
Fifteen-year guarantee against rusting through on the inside and outside of hot-dip galvanized compressed air tanks
Energy savings with frequency-controlled compressors:
Based on the frequency converter technology, the delivery quantity of the compressor adapts to the actual consumption. The electronic control monitors the engine and compressor speed and keeps the network pressure constant. The user receives advanced cutting-edge technology in the smallest of spaces.
Your advantages:
Active energy saving
Ideal for frequently changing compressed air consumption
The speed-controlled compressor achieves maximum efficiency and keeps the network pressure constant, even when consumption fluctuates greatly.
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Two-cylinder high-performance units made of gray cast iron for a long service life
Aftercooler with cooling fins ensures a low tank inlet temperature and thus less moisture in the compressed air
Ten-year guarantee against rusting through on powder-coated compressed air tanks
Two-cylinder high-performance units made of gray cast iron for a long service life
Large fan wheel and a cooling air baffle on the cylinder for optimum cooling of the compressor
Quality electric motor with high starting torque
Electric motor equipped with motor protection switch
Aftercooler with cooling fins ensures a low tank inlet temperature and therefore less moisture in the compressed air
Sturdy metal belt guard
400 volt models with phase inverter as standard for easy manual reversal of the direction of rotation
Compressed air tank equipped with safety valve, tank pressure gauge and condensate drain valve
Including all safety devices
Completely ready for connection
Filter pressure regulator with one pressure gauge for regulated compressed air cleaned of condensate, dirt and oil, second pressure gauge for tank pressure
Ten-year guarantee against rusting through on powder-coated compressed air tanks
Includes high-quality one composite safety coupling and high-quality CONDOR pressure switch
Flexible armored hose line with heat protection for long service life without vibration breakage
Ergonomic handle, rubber handle and transport handle on the compressed air tank for convenient transportation
Sturdy steering chassis with parking brake in combination with large, puncture-proof wheels for comfortable transportation
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
Innovative LOGIN control with 4.3" touch screen for easy operation and full control of all functions.
Energy-efficient IE4 motor
Rotation direction control for the motor, prevents damage during start-up or after a change of stand location
High cooling effect and low noise level due to thermostatically controlled radial fan
Optimum operating temperature and low fluctuation of oil temperature due to thermostatically controlled radial fan, optimum cooling air flow and generously dimensioned heat exchangers
Aftercooler reduces the effort for drying and filtration of the generated compressed air
Star-delta switching as standard
Easy to service: simple removal and installation of all components requiring maintenance
Manufacturer Aircraft Kompressorenbau und Maschinenhandel GmbH Gewerbestraße Ost 6, 4921 Hohenzell, Austria info@aircraft.at
