Paineilmatarvikkeet

• Compressed air tank according to AD 2000 / without fitting set / 11 and 16 bar
• Hot dip galvanized inside and outside
• Constructed in accordance with EC Directive 87/404 / EEC or PED 97/23 / EC -AD 2000, Module: H / H 1
• Operating conditions according to AD 2000 - S1 (10/2000) = arrivals and departures and 20% pressure fluctuation range
• ISO 9001:2015 certified manufacturer

• 99% separation of the precipitated condensate directly after the compressor
• For separating large amounts of condensate (water, oil) and dirt particles by centrifugal acceleration of the compressed air
• Use on aftercoolers and refrigeration dryers
• High quality corrosion protection through complete anodization
• Low-flow housing made of seawater-resistant aluminum
• Outside additionally powder-coated
• Differential pressure < 0.06 bar
• With BEKOMAT® steam trap

• Maximum mechanical efficiency
• No more drive parts required
• Reduction of moving components

• Top-efficient cooling air flow
• Special, ground valves made of stainless steel.

• Suitable for compressed air with full free passage
• Temperature resistant from -20 ° C to + 180 ° C

• Suitable for compressed air with full free passage
• Temperature resistant from -20 ° C to + 180 ° C

• Cylinders and cylinder heads with long ribs for optimum heat dissipation;
• carefully balanced crankshaft made of cast iron for better concentricity
• Stainless steel valves with high air flow
• Pulley designed as a fan
• Optimized airflow, high fan performance
• Highly efficient air filter with labyrinth intake channel for noise reduction

• Ideal in combination with prefabricated solutions
• Permanently sealed without pressing
• Installation even in confined spaces
• Detachable fittings can be reused
• Cost savings through quick assembly

• Permanently sealed without pressing
• Cost savings through quick and easy assembly
• Ideal in combination with prefabricated solutions
• Compatible with other standards-compliant pipes
• No confusion of contours possible
• Installation even in confined spaces
• Extraction forces far beyond the requirements of the standard
• Pipe components can be dismantled and reused
• Numerous national and international approvals
• O-rings included

• Maximum mechanical efficiency
• No more drive parts required
• Reduction of moving components

• Top-efficient cooling air flow
• Special, ground valves made of stainless steel.

• Very smooth inner surfaces, better flow
• well proven for years
• pressure and temperature resistant
• vibration and impact resistant
• resistant to corrosion and aging
• low weight

operating temperatur

• with continuous load: -60 ° C to +100 ° C (air)

• Density, at 20 ° C: 1.04 g / cm
• linear expansion coefficient: 15 · 10-5 l / K
• Melting point: approx. + 160 ° C to + 170 ° C

• Hot-dip galvanised inside and outside with fifteen-year warranty against rusting through
• Built according to EC Directive 87/404/EEC or DGRL 97/23/EC -AD 2000, module: H / H 1
• operating conditions according to AD 2000 - S1 (10/2000) = starts and stops and 20% pressure fluctuation range

• Compressed air tank according to AD 2000 / without fitting set / 11 and 16 bar
• Hot dip galvanized inside and outside
• Constructed in accordance with EC Directive 87/404 / EEC or PED 97/23 / EC -AD 2000, Module: H / H 1
• Operating conditions according to AD 2000 - S1 (10/2000) = arrivals and departures and 20% pressure fluctuation range
• ISO 9001:2015 certified manufacturer

• Compressed air tank according to AD 2000 / without fitting set / 11 and 16 bar
• Hot dip galvanized inside and outside
• Constructed in accordance with EC Directive 87/404 / EEC or PED 97/23 / EC -AD 2000, Module: H / H 1
• Operating conditions according to AD 2000 - S1 (10/2000) = arrivals and departures and 20% pressure fluctuation range
• ISO 9001:2015 certified manufacturer

• Thanks to patented technology, regular service is possible in only 30 seconds and without expensive cleaning
• Wall and floor mounting possible
• Works reliably with any steam trap
• Suitable for all common compressor oils
• Operating media: condensate (air, water, oil), non-aggressive, not suitable for emulsion
• Quick and clean change of the filter cartridge
• No settling tank necessary (no bacteria formation)
• Easy installation due to compact design and small dimensions
• Connection via quick couplings

• Multi-stage oil-water separation via an oil-attracting filter and activated carbon
• After the end of the service life of the filter element this is unscrewed and disposed of completely
• Filter element is tightly closed with plastic cover, so that residual condensate can remain in it
• Locked filter element can be disposed of according to current regulations

• after occurrence of one of the following three cases:
• 4,000 operating hours of the compressor at compressor oil transfer of 2.5 mg / m3
• Discoloration of the polypropylene medium - analysis by simple visual inspection
• At the latest after 12 months (regardless of the operating hours of the compressor)

• Cylinders and cylinder heads with long ribs for optimum heat dissipation;
• carefully balanced crankshaft made of cast iron for better concentricity
• Stainless steel valves with high air flow
• Pulley designed as a fan
• Optimized airflow, high fan performance
• Highly efficient air filter with labyrinth intake channel for noise reduction

• For approximate determination of the residual oil content of the compressed air on the activated carbon filters AWM

• Simple and quick installation
• Ideal for compressed air and liquids
• Can be assembled without tools
• Fast, multiple disconnections possible
• Very good flow properties